Toyota Corolla (E120): Replacement

Hint

: for parking brake cable assy no.2, Perform the same procedure to the parking brake cable assy no.3.

1. Remove rear wheel

2. Remove rear brake drum sub–assy

3. Remove rear brake automatic adjust lever lh

4. Remove front brake shoe 

sst 09718–00010

5. Remove parking brake shoe strut set lh

6. Remove rear brake shoe 

sst 09718–00010

7. Disconnect parking brake cable assy no.3

  1. Remove the bolt, and disconnect the parking brake cable assy no.3 From the backing plate.

8. Remove exhaust pipe assy front

9. Remove front floor heat insulator no.1

10. Remove front floor heat insulator no.2

11. Remove fuel tank protector no.1

  1.  remove the 5 nuts and fuel tank protector no.1.

12. Remove parking brake cable assy no.3

  1. Using a clip remover, disconnect the skid control sensor wire harness clip from the clamp.
  2.  remove the 4 bolts and cable retainer from the body.
  3.  disconnect the parking brake cable assy no.3 From the equalizer, and remove the parking brake cable assy no.3.

13. Install parking brake cable assy no.3

  1.  connect the parking brake cable assy no.3 To the equalizer.
  2. Install the parking brake cable assy no.3 With the 4 bolts and cable retainer.

    Torque: 5.4 Nvm (55 Kgf·cm, 48 in.Vlbf)

  1. Connect the skid control sensor wire harness clip to the clamp.

14. Install fuel tank protector no.1

  1.  install the fuel tank protector no.1 With the 5 nuts.

    Torque: 5.5 Nvm (55 Kgf·cm, 48 in.Vlbf)

15. Install front floor heat insulator no.2

16. Install front floor heat insulator no.1

17. Install exhaust pipe assy front

18. Connect parking brake cable assy no.3

  1. Connect the parking brake cable assy no.3 To the backing plate with the bolt.

    Torque: 7.8 Nvm (80 Kgf·cm, 69 in.Vlbf)

19. Application high temperature grease

20. Install rear brake shoe 

sst 09718–00010

21. Install parking brake shoe strut set lh

22. Install front brake shoe 

sst 09718–00010

23. Install rear brake automatic adjust lever lh

24. Check rear drum brake installation

25. Install rear brake drum sub–assy

26. Adjust rear drum brake shoe clearance

27. Install rear wheel

torque: 103 nvm (1,050 Kgf·cm, 76 ft·lbf)

28. Inspect parking brake lever travel

29. Adjust parking brake lever travel

30. Check exhaust leakage

    Share this page:

    Other materials:

    Power point socket assy rr
    Replacement Hint: components: 1. Remove parking brake hole cover sub–assy 2. Remove floor shift shift lever knob sub–assy (m/t transaxle) 3. Remove console panel upper 4. Remove console box carpet 5. Remove console box sub–assy rear (m/t transaxle) 6. Remove console box sub–assy rear ...

    Monitor description
    The battery supplies electricity to the ecm even when the ignition switch is off. This electricity allows the ecm store data such as dtc history, freeze frame data, fuel trim values, and other data. If the battery voltage falls below a minimum level, the ecm will conclude that there is a fault ...

    Replacement
    1. Remove radiator grille sub–assy 2. Remove front bumper cover 3. Remove fog lamp assy lh Remove a nut and release a claw.  remove the fog light assy lh. 4. Put vehicle these conditions 5. Adjust fog light aim 6. Check fog light aim ...