Toyota Tacoma manuals

Toyota Corolla Owners Manual: Installing child restraints using a seat belt

■ Rear-facing - Infant seat/convertible seat

1 Place the child restraint system on the rear seat facing the rear of the vehicle.

2 Run the seat belt through the child restraint system and insert the plate into

2 Run the seat belt through the child restraint system and insert the plate into the buckle. Make sure that the belt is not twisted.

3 Fully extend the shoulder belt and allow it to retract to put it in lock mode.

3 Fully extend the shoulder belt and allow it to retract to put it in lock mode. In lock mode, the belt cannot be extended.

4 While pushing the child restraint system down into the rear seat, allow the

4 While pushing the child restraint system down into the rear seat, allow the shoulder belt to retract until the child restraint system is securely in place.

After the shoulder belt has retracted to a point where there is no slack in the belt, pull the belt to check that it cannot be extended.

■ Forward-facing - Convertible seat

■ Forward-facing - Convertible seat

1 Place the child restraint system on the seat facing the front of the vehicle.

If your child restraint system interferes with a head restraint and cannot be installed properly, install the child restraint system after removing the head restraint.

2 Run the seat belt through the child restraint system and insert the plate into

2 Run the seat belt through the child restraint system and insert the plate into the buckle. Make sure that the belt is not twisted.

3 Fully extend the shoulder belt and allow it to retract to put it in lock mode.

3 Fully extend the shoulder belt and allow it to retract to put it in lock mode. In lock mode, the belt cannot be extended.

4 While pushing the child restraint system into the rear seat, allow the shoulder

4 While pushing the child restraint system into the rear seat, allow the shoulder belt to retract until the child restraint system is securely in place.

After the shoulder belt has retracted to a point where there is no slack in the belt, pull the belt to check that it cannot be extended.

5 If the child restraint has a top tether strap, the top tether strap should

5 If the child restraint has a top tether strap, the top tether strap should be latched onto the top tether strap anchor.

■ Booster seat

1 Place the child restraint system on the seat facing the front of the vehicle.

2 Sit the child in the child restraint system. Fit the seat belt to the child

2 Sit the child in the child restraint system. Fit the seat belt to the child restraint system according to the manufacturer's instructions and insert the plate into the buckle. Make sure that the belt is not twisted.

Check that the shoulder belt is correctly positioned over the child's shoulder

Check that the shoulder belt is correctly positioned over the child's shoulder and that the lap belt is as low as possible.

Installation with LATCH system
1 Widen the gap between the seat cushion and seatback slightly. ► Type A 2 Latch the hooks of the lower straps onto the LATCH anchors. If the child restraint has a top tether strap, the top ...

Removing a child restraint installed with a seat belt
Push the buckle release button and fully retract the seat belt. ...

Other materials:

Switching on/off and interrupting cruise control
Switching on Press the button on the steering wheel. The indicator lights in the instrument cluster light up and the mark in the speedometer is set to the current speed. Cruise control is active. The current speed is maintained and stored as desired speed. DSC Dynamic Stability Control is switche ...

Combination meter assy
Overhaul Hint: components: 1. Remove meter hood sub–assy 2. Remove combination meter assy Remove the screw.  disengage the 2 clips as shown in the illustration.  disconnect the connector, then remove the combination meter. 3. Remove combination meter glass Dise ...

Starting system
Inspection 1. Inspect starter assy Notice: these tests must be performed within 3 to 5 seconds to prevent burnout of the coil.  perform the pull–in test.  Remove the nut, then disconnect the lead wire from terminal c. Connect the battery to the starter repair ...

© 2011-2023 Copyright www.tcorolla.net