Toyota Corolla (E120): Floor shift cable transmission control shift

Replacement

Hint

: components:

1. Remove air conditioner unit assy

Hint

: refer to the instructions for removal of the air conditioner unit assy.

2. Separate air bag sensor assy center

  1.  remove the 3 bolts, separate the airbag sensor assy center.

3. Remove exhaust pipe assy

4. Remove front floor heat insulator no.1

  1.  remove the 3 nuts and heat insulator no.1.

5. Remove floor shift cable transmission control shift

  1. Remove the clip and washer, separate the top of the shift cable from the transaxle.
  2.  remove the clip, separate the shift cable from the control cable bracket.

  1. Remove the 2 nuts and clamp.

  1. Using a screwdriver, release the cable outer spring.
  2.  turn the lock, separate the shift cable from the shift lever retainer.

  1. Separate the end of the shift cable from the shift lever assy.

  1. Remove the 2 bolts and retainer from the floor.
  2.  pull out the control cable assy from the floor.

  1. Remove the retainer from the grommet.

6. Install floor shift cable transmission control shift

  1. Put the control cable assy through the floor hole and retainer.
  2.  install the retainer to the grommet.

Notice

: fit 4 projections of the grommet into 4 holes of the retainer.

  1. Install the control cable assy with the 2 bolts.

    Torque: 5.0 Nvm (51 Kgf·cm, 44 in.Vlbf)

  1. Connect the end of the shift cable to the shift lever assy.

  1. Connect the shift cable to the retainer of shift lever assy, turn the lock.

    Notice

    : the projecting part of the lock should face upward when the shift cable is installed.

  2.  install the cable outer spring to the lock.

    Notice

    : make sure that after installation the cable outer spring is moved to the place shown in the illustration.

  1. Install the clamp with the 2 nuts.

    Torque: 5.0 Nvm (51 Kgf·cm, 44 in.Vlbf)

  1. Connect the shift cable to the control cable bracket, install a new clip.
  2.  connect the shift cable to the transaxle, install the washer and clip.

7. Install front floor heat insulator no.1

  1. install the heat insulator no.1 With the 3 nuts.

    Torque: 5.5 Nvm (56 Kgf·cm, 49 in.Vlbf)

8. Install exhaust pipe assy

9. Connect air bag sensor assy center

  1. install the airbag sensor assy center with the 3 bolts.

    Torque: 17.5 Nvm (178 Kgf·cm, 13 ft·lbf)

10. Inspect srs warning light

    Share this page:

    Other materials:

    Eco Driving Indicator Light customization (except vehicles with a manual transmission)
    Eco Driving Indicator Light can be activated or deactivated. 1 While the odometer is being displayed, press and hold the “DISP” switch to display the Eco Driving Indicator Light customization screen. 2 Press the “DISP” switch to set Eco Driving Indicator Light to on or off. 3 Press and ...

    Warning buzzer does not sound (key reminder warning, light reminder warning)
    Wiring diagram Inspection procedere 1 Check buzzer Check that all of the warning buzzers sound. 2 Inspect front door courtesy lamp switch assy 3 Inspect un–lock warning switch assy 4 Check harness and connector(between un–lock warning switch and combination meter as ...

    Spiral cable sub–assy
    Components Replacement Hint: components: 1. Precaution 2. Disconnect battery negative terminal 3. Place front wheels facing straight ahead  check that the front wheels are facing straight ahead. 4. Remove horn button assy 5. Remove steering wheel assy  sst 09950–50013 ...