Toyota Corolla (E120): Floor shift cable transmission control select

Replacement

Hint

: components:

1. Remove air conditioner unit assy

H

int

: refer to the instructions for removal of the air conditioner unit assy.

2. Separate air bag sensor assy center

  1.  remove the 3 bolts, separate the airbag sensor assy center.

3. Remove exhaust pipe assy

4. Remove front floor heat insulator no.1

  1.  remove the 3 nuts and heat insulator no.1.

5. Remove floor shift cable transmission control select

  1. Remove the clip and washer, separate the top of the select cable from the transaxle.
  2.  remove the clip, separate the select cable from the control cable bracket.

  1. Remove the 2 nuts and clamp.

  1. Using a screwdriver, release the cable outer spring.
  2.  turn the lock, separate the select cable from the shift lever retainer.

  1. Separate the end of the select cable from the shift lever assy.

  1. Remove the 2 bolts and retainer from the floor.
  2.  pull out the control cable assy from the floor.

  1. Remove the retainer from the grommet.
  2.  remove the select cable from the grommet.

6. Install floor shift cable transmission control select

  1. Install the select cable to the grommet.
  2.  install the retainer to the grommet.

Notice

: fit 4 projections of the grommet into 4 holes of the retainer.

  1. Install the control cable assy with the 2 bolts.

    Torque: 5.0 Nvm (51 Kgf·cm, 44 in.Vlbf)

  1. Connect the end of the select cable to the shift lever assy.

  1. Connect the select cable to the retainer of shift lever assy, turn the lock.

    Notice

    : the projecting part of the lock should face upward when the select cable is installed.

  2.  install the cable outer spring to the lock.

    Notice

    : make sure that after installation the cable outer spring is moved to the place shown in the illustration.

  1. Install the clamp with the 2 nuts.

    Torque: 5.0 Nvm (51 Kgf·cm, 44 in.Vlbf)

  1. Connect the select cable to the control cable bracket, install a new clip.
  2. connect the select cable to the transaxle, install the washer and clip.

7. Install front floor heat insulator no.1

  1.  install the heat insulator no.1 With the 3 nuts.

8. Install exhaust pipe assy

9. Connect air bag sensor assy center

  1.  install the airbag sensor assy center with the 3 bolts.

    Torque: 17.5 Nvm (178 Kgf·cm, 13 ft·lbf)

10. Inspect srs warning light

    Share this page:

    Other materials:

    Overhaul
    1. Drain clutch fluid 2. Remove brake master cylinder sub–assy 3. Remove brake booster assy 4. Disconnect clutch reservoir tube Loosen the clip and disconnect the clutch reservoir tube from the clutch master cylinder assy. Hint: use a container to catch the fluid. 5. Disconnect ...

    Receiving a phone call
    Answering the phone Press the off-hook switch. Refusing a call Press the on-hook switch. Receiving a call when on another call Press the off-hook switch. Pressing the off-hook switch again returns you to the previous call. Adjusting the ringtone volume when receiving a call Change the ringto ...

    Engine coolant
    The coolant level is satisfactory if it is between the “F” and “L” lines on the reservoir when the engine is cold. 1 Reservoir cap 2 “F” line 3 “L” line If the level is on or below the “L” line, add coolant up to the “F” line. ■Coolant selection Only use “To ...