Toyota Corolla (E120): Inspection procedure

1 Check side squib(rh) circuit(airbag sensor assy center – front seat airbag assy rh)

  1. Disconnect the negative (–) terminal cable from the battery, and wait at least for 90 seconds.
  2.  disconnect the connectors between the airbag sensor assy center and the front seat airbag assy (rh).
  3.  for the connector (on the front seat airbag assy side) between the airbag sensor assy center and the front seat airbag assy (rh), measure the resistance between sfr+ and body ground.

    Ok: resistance: 1 mΩ or higher

2 Check air bag sensor assy center

2 Check air bag sensor assy center

Sst 09843–18040

  1. Connect the connector to the airbag sensor assy center.
  2.  using a service wire, connect sfr+ and sfr– of the connector (on the front seat airbag assy side) between the airbag sensor assy center and the front seat airbag assy (rh).
  3.  connect the negative (–) terminal cable to the battery, and wait at least for 2 seconds.
  4.  turn the ignition switch to on, and wait at least for 20 seconds.
  5.  clear the dtc stored in memory .
  6. turn the ignition switch to lock, and wait at least for 20 seconds.
  7.  turn the ignition switch to on, and wait at least for 20 seconds.
  8.  check the dtc .

    Ok: dtc b0112/41 is not output.

Hint

: codes other than code b0112/41 may be output at this time, but they are not relevant to this check.

3 Check side squib(rh)

3 Check side squib(rh)

Sst 09843–18040

  1. Turn the ignition switch to lock.
  2.  disconnect the negative (–) terminal cable from the battery, and wait at least for 90 seconds.
  3.  connect the front seat airbag assy (rh) connector.
  4.  connect the negative (–) terminal cable to the battery, and wait at least for 2 seconds.
  5.  turn the ignition switch to on, and wait at least for 20 seconds.
  6.  clear the dtc stored in memory .
  7.  turn the ignition switch to lock, and wait at least for 20 seconds.
  8.  turn the ignition switch to on, and wait at least for 20 seconds.
  9.  check the dtc .

    Ok: dtc b0112/41 is not output.

Hint

: codes other than code b0112/41 may be output at this time, but they are not relevant to this check.

4 Use simulation method to check

4 Use simulation method to check

Replace all srs components including the wire harness

Replace all srs components including the wire harness

    Share this page:

    Other materials:

    Automatic transaxle fluid (atm)
    On–vehicle inspection 1. Check the fluid level Hint: drive the vehicle so that the engine and transaxle are at normal operating temperature. Fluid temperature: 70 – 80 °c (158 – 176 °f)  park the vehicle on a level surface and set the parking brake.  with the engin ...

    When stopping the engine with the shift lever in a position other than P (vehicles with a continuously variable transmission)
    If the engine is stopped with the shift lever in a position other than P, the engine switch will not be turned off but instead be turned to ACCESSORY mode. Perform the following procedure to turn the switch off: 1 Check that the parking brake is set. 2 Shift the shift lever to P. ► Vehi ...

    Overhaul
    1. Remove manual transmission filler plug Remove the manual transmission filler plug and gasket from the manual transmission case. 2. Remove drain (mtm) plug sub–assy Remove the drain (mtm) plug sub–assy and gasket from the manual transmission case. 3. Remove speedomete ...