Toyota Corolla (E120) 2002–2008 Repair Manual / Diagnostics / Supplemental restraint system / Short in p/t squib (lh) circuit (to b+) / Inspection procedure
Toyota Corolla (E120): Inspection procedure
1 Check p/t squib(lh) circuit(airbag sensor assy center – front seat outer belt assy lh)

- Disconnect the negative (–) terminal cable from the battery, and wait at least for 90 seconds.
- disconnect the connectors between the airbag sensor assy center and the seat belt pretensioner (lh).
- connect the negative (–) terminal cable to the battery, and wait at least for 2 seconds.
- turn the ignition switch to on.
- for the connector (on the seat belt pretensioner side) between
the airbag sensor assy center and the seat belt pretensioner
(lh), measure the voltage between pl+ and
body ground.
Ok: voltage: below 1v


2 Check air bag sensor assy center
Sst 09843–18040

- Turn the ignition switch to lock.
- disconnect the negative (–) terminal cable from the battery and wait at least for 90 seconds.
- connect the connector to the airbag sensor assy center.
- using a service wire, connect pl+ and pl– of the connector (on the seat belt pretensioner side) between the airbag sensor assy center and the seat belt pretensioner (lh).
- connect the negative (–) terminal cable to the battery, and wait at least for 2 seconds.
- turn the ignition switch to on, and wait at least for 20 seconds.
- clear the dtc stored in memory .
- turn the ignition switch to lock, and wait at least for 20 seconds.
- turn the ignition switch to on, and wait at least for 20 seconds.
- check the dtc .
Ok: dtc b0138/72 is not output.
Hint
: codes other than code b0138/72 may be output at this time, but they are not relevant to this check.


3 Check p/t squib (lh)
Sst 09843–18040

- Turn the ignition switch to lock.
- disconnect the negative (–) terminal cable from the battery, and wait at least for 90 seconds.
- connect the seat belt pretensioner (lh) connector.
- connect the negative (–) terminal cable to the battery, and wait at least for 2 seconds.
- turn the ignition switch to on, and wait at least for 20 seconds.
- clear the dtc stored in memory .
- turn the ignition switch to lock, and wait at least for 20 seconds.
- turn the ignition switch to on, and wait at least for 20 seconds.
- check the dtc .
Ok: dtc b0138/72 is not output.
Hint
: codes other than code b0138/72 may be output at this time, but they are not relevant to this check.


4 Use simulation method to check


Replace all srs components including the wire harness
Other materials:
Overhaul
Notice:
when using a vise, do not over tighten.
When installing, coat the parts indicated by the arrows with power
steering fluid .
1. Remove front wheel rh
2. Drain power steering fluid
3. Remove engine under cover rh
4. Remove fan and generator v belt
5. Disconnect oil reservoir to ...
Rear seats
The seatbacks of the rear seats can be folded down.
The seatbacks of the rear seats can be folded down.
1 Stow the rear outside seat belt buckles and stow the rear center seat belt
buckle as shown.
2 Pull the seatback lock release knob and fold the seatback down.
CAUTION
■When foldi ...
Valve clearance
Adjustment
1. Remove cylinder head cover no.2
Remove the 2 nuts, 2 clips and cylinder head cover.
2. Disconnect engine wire
Remove the 5 clamps from the 5 clamp brackets.
Disconnect the 4 ignition coil connectors.
Remove the bolt and nut installing the engine wire ...


