Toyota Tacoma manuals

Toyota Corolla Repair Manual: Vehicle lift and support locations

Toyota Corolla Repair Manual / Introduction / Repair instruction / Vehicle lift and support locations

1. Notice about vehicle condition when jacking up

  1. As a rule, the vehicle must be unloaded when jacking up. Never jack up or lift up the vehicle loaded with things of heavy weight.
  2.  when removing any parts of heavy weight like the engine and transmission, the center of gravity of the vehicle moves. Place a balance weight so as to keep it from rolling, or hold the jacking support location using the mission jack.

2. Notice for using 4 post lift

  1. Follow the instruction manual for a safety operation.
  2.  do not damage tires or wheels with a free wheel beam.
  3.  using a wheel stopper, fix the vehicle.

3. Notice for using jack and safety stand

  1.  work in a flat place using a wheel stopper at all times.
  2.  use a safety stand with a rubber attachment, as shown in the illustration.
  3.  support the specified location with a jack and safety stand accurately.
  4.  when jacking up the front wheels, release the parking brake and place wheel stoppers only behind the rear wheels. When jacking up the rear wheels, place wheel stoppers only in front of the front wheels.
  5.  do not work or leave the vehicle supported only by a jack.

    Be sure to support the vehicle with a safety stand.

  1. When jacking up only the front wheels or only the rear wheels, place wheel stoppers to both sides of the wheels that contact ground.
  2.  when jacking down the vehicle with its front wheels jacked up, release the parking brake and place wheel stoppers only in front of the rear wheels. When jacking down the vehicle with its rear wheels jacked up, place wheel stoppers only behind the front wheels.

4. Notice for using swing arm type lift

4. Notice for using swing arm type lift

  1. Follow the instruction manual of the lift for a safe operation.
  2.  use a cradle with a rubber attachment, as shown in the illustration.
  3.  set in the vehicle so as to make its center of gravity as close as possible to the center of the lift. (”L” becomes short.)
  4.  place the vehicle horizontally by adjusting the height of the cradle, and match the groove of the cradle and the safety stand support location accurately.
  5.  be sure to lock the swing arm during the operation.
  6.  lift the vehicle up until the tires float, and shake the vehicle to make sure that the vehicle is stable.

5. Notice for using plate type lift

  1. Follow the instruction manual of the lift for a safe operation.
  2.  use a plate lift attachment.
  3.  be sure to set the vehicle to the specified position.
Right and left set position
  • Place the vehicle over the center of the lift.
Front and rear set position
  • Align the cushion gum ends of the plate with the attachment lower ends (a and c).
  • Align the attachment upper end (b) with the rocker flange front side notch.
  1. Lift the vehicle up until the tires float a bit, and shake the vehicle to make sure that the vehicle is stable.

How to troubleshoot ecu controlled

For vehicles equipped with catalytic converter
Caution: if large amount of unburned fuel flows into the converter, it may cause overheating and a fire hazard. To prevent this, observe the following precautions. Use only unleaded gasoline ...

How to troubleshoot ecu controlled systems
...

Other materials:

Overhaul
1. Drain clutch fluid 2. Disconnect clutch release cylinder to flexible hose tube Using sst, disconnect the flexible hose tube. Sst 09023–00100 Hint: use a container to catch the fluid. 3. Remove clutch release cylinder assy Remove the 3 bolts, clutch release cylinder assy an ...

Concept, General information, Safety information
Concept The lane departure warning alerts when the vehicle on roads with lane markings is about to leave the lane. General information This camera-based system warns starting at a minimum speed. The minimum speed is country-specific and is displayed in the menu for the intelligent Safety systems. ...

Air bag sensor front lh
Components Replacement Hint: components: 1. Precaution 2. Disconnect battery negative terminal 3. Remove air bag sensor front lh Disconnect the connector from the airbag sensor front lh.  remove the 2 bolts and airbag sensor front lh. 4. Inspect air bag sensor front lh ...

© 2011-2023 Copyright www.tcorolla.net