Toyota Tacoma manuals

Toyota Corolla Repair Manual: Inspection procedure

1 Check p/t squib(rh) circuit(airbag sensor assy center front seat outer belt assy rh)

  1. Disconnect the negative () terminal cable from the battery, and wait at least for 90 seconds.
  2.  disconnect the connectors between the airbag sensor assy center and the seat belt pretensioner (rh).
  3.  for the connector (on the seat belt pretensioner side) between the airbag sensor assy center and the seat belt pretensioner (rh), measure the resistance between pr+ and pr.

    Ok: resistance: below 1 Ω

2 Check air bag sensor assy center

2 Check air bag sensor assy center

Sst 0984318040

  1. Connect the connector to the airbag sensor assy center.
  2.  using a service wire, connect pr+ and pr of the connector (on the seat belt pretensioner side) between the airbag sensor assy center and the seat belt pretensioner (rh).
  3.  connect the negative () terminal cable to the battery, and wait at least for 2 seconds.
  4.  turn the ignition switch to on, and wait at least for 20 seconds.
  5.  clear the dtc stored in memory .
  6.  turn the ignition switch to lock, and wait at least for 20 seconds.
  7.  turn the ignition switch to on, and wait at least for 20 seconds.
  8.  check the dtc .

    Ok: dtc b0131/64 is not output.

Hint

: codes other than code b0131/64 may be output at this time, but they are not relevant to this check.

3 Check p/t squib (rh)

3 Check p/t squib (rh)

Sst 0984318040

  1. Turn the ignition switch to lock.
  2.  disconnect the negative () terminal cable from the battery, and wait at least for 90 seconds.
  3.  connect the seat belt pretensioner (rh) connector.
  4.  connect the negative () terminal cable to the battery, and wait at least for 2 seconds.
  5.  turn the ignition switch to on, and wait at least for 20 seconds.
  6.  clear the dtc stored in memory .
  7.  turn the ignition switch to lock, and wait at least for 20 seconds.
  8.  turn the ignition switch to on, and wait at least for 20 seconds.
  9.  check the dtc .

    Ok: dtc b0131/64 is not output.

Hint

: codes other than code b0131/64 may be output at this time, but they are not relevant to this check.

Use simulation method to check

Use simulation method to check

Circuit description
The p/t squib circuit (rh) consists of the airbag sensor assy center and seat belt pretensioner (rh). It causes the srs to deploy when the srs deployment conditions are satisfied. Dtc b0131/64 ...

Short in p/t squib (rh) circuit (to ground)
Dtc b0132/61 short in p/t squib (rh) circuit (to ground) ...

Other materials:

Torque converter clutch and drive plate (atm)
Inspection 1. Inspect torque converter clutch assy Inspect the oneway clutch.  Set sst into the inner race of the oneway clutch. Sst 0935032014 (0935132010)  set sst so that it fits in the notch of the converter hub and outer race of the oneway clutch. Sst 09350 ...

Steering wheel audio switches
Some audio features can be controlled using the switches on the steering wheel. Operation may differ depending on the type of audio system or navigation system. For details, refer to the manual provided with the audio system or navigation system. Operating the audio system using the steering whe ...

Floor shift parking lock cable assy (atm)
Replacement 1. Precaution 2. Disconnect battery negative terminal 3. Place front wheels facing straight ahead 4. Remove horn button assy 5. Remove steering wheel assy sst 0995050013 (0995105010, 0995205010, 0995305020, 0995405021) 6. Remove steering column cover 7. Remove console pan ...

2011-2019 Copyright www.tcorolla.net