Toyota Corolla Repair Manual: Door control transmitter
Registration
1. Registration of recognition code
Hint
:
- the add mode is used to retain the already registered codes while
registering a new recognition code.
This mode is used when adding a transmitter. If the number of the registered
codes exceeds 4, the
previously registered code will be correspondingly erased in order, starting
from the first registered
code.
- The rewrite mode is used to erase all the previously registered codes
and register only new recognition
codes. This mode is used when exchanging the transmitter or the door control
receiver for new one.
- The prohibition mode is used to erase all the registered codes and
cancel the wireless door lock function.
Use this mode when the transmitter is lost.
- The confirmation mode is to confirm how many recognition codes have
already been registered before
an additional registration of a recognition code.
- All the following registration procedures must be performed in order
continuously.
- the vehicle should be in the following conditions.
- The key is not inserted in the ignition key cylinder.
- Driver’s door is opened. (The other doors are closed)
- driver’s door is unlocked.
- perform the following operations to select the desired mode.
- Insert and remove the key from the ignition switch twice within 5
seconds.
- After the above operations, close and open the driver door twice
within 40 seconds. Then insert
the key into the ignition key cylinder and remove it.
- After the above operations, close and open the driver door twice
within 40 seconds. Then insert
the key into the ignition key cylinder and close the door.
- Turn the ignition switch from lock to on and back to lock at
approximately 1 second interval
1 to 5 times to select a mode (see the table below). Then remove the key
from the ignition key
cylinder.

Notice
:
if the number of the on–lock operation of the ignition switch is 0, 4 or 6 or
more, there will be no
response (power door lock and unlock operation) to inform which mode has been
selected.
- After selecting a mode, the integration relay automatically
performs the power door
lock–unlock operation within 3 seconds to inform the selected mode (see the
table below).
Hint
:
- in the confirmation mode, when the operation is performed twice, it
directs that 2 types of recognition
codes have been registered.
- In the confirmation mode, if the number of the registration code is
0, the lock–unlock operation
is automatically performed 5 times.
- If the prohibition mode or confirmation mode is selected,
registration procedure is completed.

- Register the new recognition codes (add mode or rewrite mode):
- within 40 seconds after the add mode or the rewrite mode has been
selected, press the lock
and unlock switches on the transmitter switch simultaneously for 1.0 – 1.5
Seconds.
Within 3 seconds after the previous operation, press either one of the
switches for more than 1.0
Seconds.
- Within 3 seconds after the transmitter switch has been turned off,
the lock–unlock operation
will be automatically performed once if the registration of the recognition
code of the transmitter
is completed correctly. In case the lock–unlock operation is performed
twice, the registration
of recognition code has failed. Perform the registration procedure from the
beginning once
again.

- If the multiple transmitter to be registered, repeat step (c) within 40
seconds after the previous
registration.
Hint
:
- 4 types of recognition codes can be registered at one time.
- If even one of the following conditions is satisfied, the
registration mode will finish.
- 40 Seconds have elapsed while an input of each mode is ready.
- Any of the doors is opened
- the key plate is inserted in the ignition key cylinder.
- 4 Types of recognition codes are registered at once.
Replacement
1. Replace transmitter battery
Notice:
special caution should be taken for handling each component as they are
precision electronic components.
Using a screwdriver, pry out th ...
On–vehicle inspection
1. Outline of toyota vehicle intrusion protection (tvip) system
Hint:
the theft deterrent system has 2 modes; one is the active mode that is an
initially set mode and anothe ...
Other materials:
Positioning a floor jack
When using a floor jack, follow the instructions in the manual provided with
the jack and perform the operation safely.
When raising your vehicle with a floor jack, position the jack correctly.
Improper placement may damage your vehicle or cause injury.
◆ Front
◆ Rear
1 Take out ...
Calibrating the compass
The direction display deviates from
the true direction determined by the earth’s magnetic field. The amount of deviation
varies according to the geographic position of the vehicle.
If you cross over a map boundary shown in illustration, the compass will deviate.
To obtain higher precision or p ...
Other functions
■ Switching between outside air and recirculated air modes
Press .
The mode switches between outside air mode (indicator off) and recirculated air
mode (indicator on) each time is pressed.
■ Defogging the windshield
Defoggers are used to defog the windshield and front side windows ...