Toyota Corolla (E120): Floor shift cable transmission control select

Replacement

Hint

: components:

1. Remove air conditioner unit assy

H

int

: refer to the instructions for removal of the air conditioner unit assy.

2. Separate air bag sensor assy center

  1.  remove the 3 bolts, separate the airbag sensor assy center.

3. Remove exhaust pipe assy

4. Remove front floor heat insulator no.1

  1.  remove the 3 nuts and heat insulator no.1.

5. Remove floor shift cable transmission control select

  1. Remove the clip and washer, separate the top of the select cable from the transaxle.
  2.  remove the clip, separate the select cable from the control cable bracket.

  1. Remove the 2 nuts and clamp.

  1. Using a screwdriver, release the cable outer spring.
  2.  turn the lock, separate the select cable from the shift lever retainer.

  1. Separate the end of the select cable from the shift lever assy.

  1. Remove the 2 bolts and retainer from the floor.
  2.  pull out the control cable assy from the floor.

  1. Remove the retainer from the grommet.
  2.  remove the select cable from the grommet.

6. Install floor shift cable transmission control select

  1. Install the select cable to the grommet.
  2.  install the retainer to the grommet.

Notice

: fit 4 projections of the grommet into 4 holes of the retainer.

  1. Install the control cable assy with the 2 bolts.

    Torque: 5.0 Nvm (51 Kgf·cm, 44 in.Vlbf)

  1. Connect the end of the select cable to the shift lever assy.

  1. Connect the select cable to the retainer of shift lever assy, turn the lock.

    Notice

    : the projecting part of the lock should face upward when the select cable is installed.

  2.  install the cable outer spring to the lock.

    Notice

    : make sure that after installation the cable outer spring is moved to the place shown in the illustration.

  1. Install the clamp with the 2 nuts.

    Torque: 5.0 Nvm (51 Kgf·cm, 44 in.Vlbf)

  1. Connect the select cable to the control cable bracket, install a new clip.
  2. connect the select cable to the transaxle, install the washer and clip.

7. Install front floor heat insulator no.1

  1.  install the heat insulator no.1 With the 3 nuts.

8. Install exhaust pipe assy

9. Connect air bag sensor assy center

  1.  install the airbag sensor assy center with the 3 bolts.

    Torque: 17.5 Nvm (178 Kgf·cm, 13 ft·lbf)

10. Inspect srs warning light

    Share this page:

    Other materials:

    Playing an audio CD and MP3/WMA/AAC discs (Multimedia system)
    CD player operation Insert disc or select “CD” on the audio source selection screen with a disc inserted to begin listening to a CD. Audio control screen Pressing the “AUDIO” button displays the audio control screen from any screens of the selected source. 1 Audio source selection sc ...

    How to proceed with troubleshooting
    1 Vehicle brought to workshop 2 Customer problem analysis 3 Check and clear dtcs and freeze frame data 4 Problem symptom confirmation Symptom does not occur: go to step 5 Symptom occurs: go to step 6 5 Symptom simulation 6 Dtc check There is no output: go to step 7 There is outp ...

    Overhaul
    1. Inspect 1st gear thrust clearance Using a feeler gauge, measure the 1st gear thrust clearance. Standard clearance: 0.10 – 0.40 Mm (0.0039 – 0.0157 In.) 2. Inspect 2nd gear thrust clearance Using a dial indicator, measure the 2nd gear thrust clearance. Standard clearan ...