Toyota Corolla (E120): Inspection procedure

1 Check side squib(lh) circuit(airbag sensor assy center – front seat airbag assy lh)

  1. Disconnect the negative (–) terminal cable from the battery, and wait at least for 90 seconds.
  2.  disconnect the connectors between the airbag sensor assy center and the front seat airbag assy (lh).
  3.  connect the negative (–) terminal cable to the battery, and wait at least for 2 seconds.
  4.  turn the ignition switch to on.
  5.  for the connector (on the front seat airbag assy side) between the airbag sensor assy center and the front seat airbag assy (lh), measure the voltage between sfl+ and body ground.

    Ok: voltage: below 1 v

2 Check air bag sensor assy center

2 Check air bag sensor assy center

Sst 09843–18040

  1. Turn the ignition switch to lock.
  2.  disconnect the negative (–) terminal cable from the battery, and wait at least for 90 seconds.
  3.  connect the connector to the airbag sensor assy center.
  4.  using a service wire, connect sfl+ and sfl– of the connector (on the front seat airbag assy side) between the airbag sensor assy center and the front seat airbag assy (lh).
  5.  connect the negative (–) terminal cable to the battery, and wait at least for 2 seconds.
  6.  turn the ignition switch to on, and wait at least for 20 seconds.
  7.  clear the dtc stored in memory .
  8.  turn the ignition switch to lock, and wait at least for 20 seconds.
  9.  turn the ignition switch to on, and wait at least for 20 seconds.
  10.  check the dtc .

    Ok: dtc b0118/46 is not output.

Hint

: codes other than code b0118/46 may be output at this time, but they are not relevant to this check.

3 Check side squib(lh)

3 Check side squib(lh)

Sst 09843–18040

  1. Turn the ignition switch to lock.
  2.  disconnect the negative (–) terminal cable from the battery, and wait at least for 90 seconds.
  3.  connect the front seat airbag assy (lh) connector.
  4.  connect the negative (–) terminal cable to the battery, and wait at least for 2 seconds.
  5.  turn the ignition switch to on, and wait at least for 20 seconds.
  6.  clear the dtc stored in memory .
  7. turn the ignition switch to lock, and wait at least for 20 seconds.
  8.  turn the ignition switch to on, and wait at least for 20 seconds.
  9.  check the dtc .

    Ok: dtc b0118/46 is not output.

Hint

: codes other than code b0118/46 may be output at this time, but they are not relevant to this check.

4 Use simulation method to check

4 Use simulation method to check

Replace all srs components including the wire harness

Replace all srs components including the wire harness

    Share this page:

    Other materials:

    Dynamic radar cruise control
    This dynamic radar cruise control detects the presence of vehicles ahead, determines the current vehicle- to-vehicle distance, and operates to maintain a suitable distance from the vehicle ahead. The desired vehicle-to-vehicle distance can be set by operating the vehicle-to-vehicle distance switch. ...

    Vehicle identification
    ■ Vehicle identification number The vehicle identification number (VIN) is the legal identifier for your vehicle. This is the primary identification number for your Toyota. It is used in registering the ownership of your vehicle. This number is stamped on the top left of the instrument p ...

    Air outlet layout and operations
    ■ Location of air outlets The air outlets and air volume changes according to the selected air flow mode. :If equipped ■ Adjusting the position of and opening and closing the air outlets Front center Direct air flow to the left or right, up or down Front right-hand side Direct air flow to th ...