Toyota Tacoma manuals

Toyota Corolla Repair Manual: Valve clearance

Adjustment

1. Remove cylinder head cover no.2

  1. Remove the 2 nuts, 2 clips and cylinder head cover.

2. Disconnect engine wire

  1. Remove the 5 clamps from the 5 clamp brackets.
  1. Disconnect the 4 ignition coil connectors.

  1. Remove the bolt and nut installing the engine wire.

3. Remove ignition coil assy

  1. Remove the 4 bolts and 4 ignition coils.

4. Disconnect ventilation hose

  1. Disconnect the ventilation hose from the cylinder head cover.

5. Disconnect ventilation hose no.2

  1. Disconnect the ventilation hose from the cylinder head cover.

6. Remove cylinder head cover sub–assy

  1. Remove the 9 bolts, 2 seal washers, 2 nuts, 3 clamp brackets and cylinder head cover.

7. Remove engine under cover rh

8. Set no. 1 Cylinder to tdc/compression

  1. Turn the crankshaft pulley, and align its groove with timing mark ”0” of the timing chain cover.
  2. check that the point marks of the camshaft timing sprocket and vvt timing sprocket are in straight line on the timing chain cover surface as shown in the illustration.

Hint

: if not, turn the crankshaft 1 revolution (360 ) and align the marks as above.

9. Inspect valve clearance

  1. Check only the valves indicated.
  1.  Using a feeler gauge, measure the clearance between the valve lifter and camshaft.
  2.  Record the out–of specification valve clearance measurements. They will be used later to determine the required replacement valve lifter.

    Valve clearance (cold): intake 0.15 – 0.25 Mm (0.0059 – 0.0098 In.) Exhaust 0.25 – 0.35 Mm (0.0098 – 0.0138 In.)

  1.  turn the crankshaft 1 revolution (360 ) and set no. 4 Cylinder to tdc/compression.

  1. Check only the valves indicated.
  1.  Using a feeler gauge, measure the clearance between the valve lifter and camshaft.
  2.  Record the out–of specification valve clearance measurements. They will be used later to determine the required replacement valve lifter.

    Valve clearance (cold): intake 0.15 – 0.25 Mm (0.0059 – 0.0098 In.) Exhaust 0.25 – 0.35 Mm (0.0098 – 0.0138 In.)

10. Remove fan and generator v belt

  1. Turn the v–ribbed belt tensioner slowly clockwise and loosen it. Then, remove the fan and generator v belt and put back the v–ribbed belt tensioner little by little and fix it quietly.

11. Remove engine mounting insulator sub–assy rh

  1. Remove the ps oil pump reservoir and put it aside.
  2.  place a wooden block between the jack and engine, and set the jack, then remove the 4 bolts, the 2 nuts and engine mounting insulator rh.

12. Remove v–ribbed belt tensioner assy

12. Remove v–ribbed belt tensioner assy

  1. Remove the bolt, nut and v–ribbed belt tensioner.

Hint

: handle a jack up and down to remove the bolt.

13. Adjust valve clearance

Notice:

Notice

: be sure not to revolve the crankshaft without the chain tensioner.

  1. Set the no. 1 Cylinder to the tdc/compression.
  2.  place match marks on the timing chain and camshaft timing sprockets.

  1. Remove the 2 nuts and chain tensioner.

  1. Fix the camshaft with a spanner and so on, then loosen the camshaft timing gear set bolt.

Notice

: be careful not to damage the valve lifter.

  1. Loosen the camshaft bearing cap bolts on no. 2 Camshaft in the order as shown in the illustration in several passes,and remove the caps.

  1. Remove the camshaft timing gear as shown in the illustration.

  1. Loosen the camshaft bearing cap bolts on camshaft in the order as shown in the illustration in several passes,and remove the caps.

  1. Remove the camshaft with holding the timing chain.

  1. Tie the timing chain with a string as shown in the illustration.

Notice

: be careful not to drop anything inside the timing chain cover.

  1. Remove the valve lifters.
  2.  using a micrometer, measure the thickness of the removed lifter.
  3.  calculate the thickness of a new lifter so that the valve clearance comes within the specified value.

Valve clearance:

Valve clearance:
intake a = b + (c – 0.20 Mm (0.0079 In.) Exhaust a = b + (c – 0.30 Mm (0.0118 In.)

Hint

:

  1. As shown in the illustration, install the timing chain on the camshaft timing gear, with the painted links aligned with the timing marks on the camshaft timing sprocket.

  1. Examine the front marks and numbers and tighten the bolts in the order shown in the illustration.

    Torque: 13 nvm (133 Kgf·cm, 10 ft·lbf)

  1. Put the camshaft no.2 On the cylinder head with the painted links of the chain aligned with the timing mark on the camshaft timing sprocket.

  1. Tighten the camshaft timing gear set bolt temporarily.

  1. Examine the front marks and numbers and tighten the bolts in the order shown in the illustration.

    Torque: 13 nvm (133 Kgf·cm, 10 ft·lbf)

  2.  install the bearing cap no. 1.

    Torque: 23 nvm (235 Kgf·cm, 17 ft·lbf)

  1. Fix the camshaft with a spanner and so on, then tighten the camshaft timing gear set bolt.

    Torque: 54 nvm (551 Kgf·cm, 40 ft·lbf)

Notice

: be careful not damage the valve lifter.

  1. Check the match marks on the timing chain and camshaft timing sprockets, and then the alignment of the pulley groove with timing mark of the chain cover as shown in the illustration.

  1. Install chain tensioner.
  1.  Check the o–ring is clean, and set the hook as shown in the illustration.

  1. Apply engine oil to the chain tensioner and install it with the 2 nuts.

    Torque: 9.0 Nvm (92 Kgf·cm, 80 invlbf)

Notice

: when installing the tensioner, set the hook again if the hook release the plunger.

  1. Turn the crankshaft counterclockwise, and disconnect the plunger knock pin from the hook.

  1. Turn the crankshaft clockwise, and check that the slipper is pushed by the plunger.

Hint

: if the plunger does not spring out, press the slipper into the chain tensioner with a screwdriver so that the hook is released from the knock pin and the plunger springs out.

14. Install v–ribbed belt tensioner assy

  1. Install the v–ribbed belt tensioner with the nut and bolt.

    Torque:
    29 nvm (296 Kgf·cm, 21 ft·lbf) for nut 69 nvm (704 Kgf·cm, 51 ft·lbf) for bolt

15. Install engine mounting insulator sub–assy rh

  1. Install engine mounting insulator rh with the 4 bolts and the 2 nuts.

    Torque: 52 nvm (530 Kgf·cm, 38 ft·lbf)

16. Install cylinder head cover sub–assy

  1. Remove any old packing (fipg) material.
  2. apply seal packing to 2 locations as shown in the illustration.

    Seal packing: part no. 08826–00080 Or equivalent

Notice

:

  1. Install the cylinder head cover and cable bracket with the 9 bolts, 2 seal washers and 2 nuts. Uniformly tighten the bolts and nuts, in the several passes.

    Torque:
    a 11 nvm (112 Kgf·cm, 8 ft·lbf) b 9.0 Nvm (92 Kgf·cm, 80 invlbf)

17. Install ignition coil assy

  1. Install the 4 ignition coils with the 4 bolts.

    Torque: 9.0 Nvm (92 Kgf·cm, 80 in.Vlbf)

18. Install engine wire

  1. Install the engine wire with the bolt and nut.

    Torque: 9.0 Nvm (92 Kgf·cm, 80 in.Vlbf)

19. Install cylinder head cover no.2

  1. Install the cylinder head cover with the 2 nuts and 2 clips.

    Torque: 7.0 Nvm (71 Kgf·cm, 62 in.Vlbf)

20. Check engine oil leak

Fan and generator v belt
Replacement 1. Remove engine under cover rh 2. Remove fan and generator v belt Turn the v–ribbed belt tensioner slowly clockwise and loosen it. Then, remove the fan and generator v belt an ...

Partial engine assy
...

Other materials:

Correct driving posture
1 Adjust the angle of the seatback so that you are sitting straight up and so that you do not have to lean forward to steer. 2 Adjust the seat so that you can depress the pedals fully and so that your arms bend slightly at the elbow when gripping the steering wheel. 3 Lock the head restraint ...

Folding the mirrors
Push the mirror back in the direction of the vehicle’s rear. ■Mirror angle can be adjusted when ► Vehicles without a smart key system The engine switch is in the “ACC” or “ON” position. ►Vehicles with a smart key system The engine switch is in ACCESSORY or IGNITION ON mode. ...

Hood
Release the lock from the inside of the vehicle to open the hood. 1 Pull the hood lock release lever. The hood will pop up slightly. 2 Pull up the auxiliary catch lever and lift the hood. 3 Hold the hood open by inserting the support rod into the slot. CAUTION ■Pre-driving check C ...

© 2011-2024 Copyright www.tcorolla.net