Toyota Tacoma manuals

Toyota Corolla Repair Manual: Replacement

Hint

:

1. Disconnect battery negative terminal

2. Remove front seat assembly rh

3. Remove front seat inner belt assy rh

  1.  remove the nut and front seat inner belt.

4. Remove front door scuff plate rh

5. Remove rear door scuff plate rh

6. Remove front door opening trim rh

7. Remove rear door opening trim rh

8. Remove center pillar garnish lower rh

9. Remove front seat outer belt assy rh

  1. Remove the floor anchor cover.
  2.  remove the bolt and disconnect the front seat outer belt assembly rh (floor anchor side).
  3.  using a screwdriver, remove the seat belt anchor cover.

    Hint

    : tape the screwdriver tip before use.

  4.  remove the bolt and front seat outer belt (shoulder anchor side).

Notice:

Notice

:

  1. disconnect the connector and remove the bolt.

10. Remove center pillar garnish rh

11. Remove front shoulder belt anchor adjuster assy

  1.  remove the 2 bolts and front shoulder belt anchor adjuster assembly.

12. Install front shoulder belt anchor adjuster assy

  1.  install the front shoulder belt anchor adjuster assembly with the bolt.

    Torque: 41.2 Nvm (420 kgfvcm, 30 ftvlbf)

13. Install front seat outer belt assy rh

Notice:

Notice

: do not disassemble the retractor.

  1.  check the degree of tilt when beginning to lock the elr.
  1.  Check that the belt will not lock within 15 degrees of tilt in all the direction but the belt will lock over 45 degrees of tilt when moving the installed retractor gently.

If the operation is not as specified, replace the front seat outer belt assembly.

  1.  install the retractor with the 2 bolts.

    Torque:
    4.9 Nvm (50 kgfvcm, 43 in.Vlbf) (upper part of retractor) 41.2 Nvm (420 kgfvcm, 30 ftvlbf) (lower part of retractor)

  2.  install the shoulder anchor with the bolt.

    Torque: 41.2 Nvm (420 kgfvcm, 30 ftvlbf)

  3.  install the seat belt anchor cover.
  4.  install the floor anchor with the bolt.

    Torque: 41.2 Nvm (420 kgfvcm, 30 ftvlbf)

  5.  install the floor anchor cover.
  6.  check the elr lock.

Notice

: check should be performed with the assembly installed.

  1.  Check that the belt will lock when pulling out the belt quickly with the belt installed.

If the operation is not as specified, replace the front seat outer belt assembly.

14. Install front seat inner belt assy rh

  1.  install the front seat inner belt assembly rh with the nut.

    Torque: 41.2 Nvm (420 kgfvcm, 30 ftvlbf)

Components
...

Disposal
Hint: when scrapping vehicles epuipped with a seat belt pretensioner or disposing of a front seat outer belt (with seat belt pretensioner) always first active the seat belt pretensioner in accor ...

Other materials:

If the shift lever cannot be shifted from P (except vehicles with a manual transmission)
If the shift lever cannot be shifted with your foot on the brake pedal, there may be a problem with the shift lock system (a system to prevent accidental operation of the shift lever). Have the vehicle inspected by your Toyota dealer immediately. The following steps may be used as an emergency ...

Follow the correction procedures. (vehicles with a smart key system and with a drive monitor display)
After taking the specified steps to correct the suspected problem, check that the warning light turns off. ■SRS warning light This warning light system monitors the airbag sensor assembly, front impact sensors, side impact sensors (front door), side impact sensors (front), side impac ...

Unlocking and locking the doors from the outside
◆ Smart key system (if equipped) Carry the electronic key to enable this function. 1 Grip the driver’s door handle to unlock the door. Grip the passenger’s door handle to unlock all the doors.* Make sure to touch the sensor on the back of the handle. The doors cannot be unlocked for 3 s ...

© 2011-2024 Copyright www.tcorolla.net