Toyota Tacoma manuals

Toyota Corolla Repair Manual: Replacement

1. Remove instrument panel sub–assy lower

2. Remove clutch pedal spring

3. Remove clutch master cylinder push rod clevis w/hole pin

  1. Remove the clip and hole pin.

4. Remove clutch pedal support sub–assy

  1. W/ cruise control: disconnect the clutch switch assy connector.
  2.  disconnect the clutch start switch assy connector.
  3.  remove the 2 nuts, bolt and clutch pedal support assy.

5. Remove clutch pedal sub–assy

  1. Remove the bolt and nut.
  2.  remove the clutch pedal sub–assy from the clutch pedal support.

6. Remove clutch pedal pad

7. Remove clutch pedal bush

  1. Remove the 2 bushes from the clutch pedal.

8. Remove clutch pedal no.1 Cushion

  1. Using needle–nose pliers, remove the no.1 Cushion from the clutch pedal.

9. Remove clutch master cylinder push rod clevis bush

  1. Using a 8 mm hexagon wrench and a hammer, remove the clevis bush from the clutch pedal sub–assy.

10. Install clutch master cylinder push rod clevis bush

  1. Apply mp grease to inside of a new clevis bush.
  2.  install the clevis bush to the clutch pedal.

Hint

: install the clevis bush from the right side of the vehicle.

11. Install clutch pedal no.1 Cushion

  1. Using needle–nose pliers, install the no.1 Cushion to the clutch pedal

12. Install clutch pedal bush

  1. Apply mp grease to both side of 2 new bushes.
  2.  install the 2 bushes to the clutch pedal.

13. Install clutch pedal pad

14. Install clutch pedal sub–assy

  1. Install the clutch pedal sub–assy to the clutch pedal support with the bolt and nut.

    Torque: 36.8 Nvm (375 Kgf·cm, 27 ft·lbf)

Hint

: install the bolt from the right side of the vehicle. 15. Install clutch pedal support sub–assy

  1. Install the clutch pedal support to the vehicle with the 2 nuts and bolt.

    Torque:
    bolt: 19.1 Nvm (195 Kgf·cm, 14 ft·lbf) nut: 11.8 Nvm (120 Kgf·cm, 9 ft·lbf)

  2.  connect the clutch start switch assy connector.
  3.  w/ cruise control: connect the clutch switch assy connector.

16. Install clutch master cylinder push rod clevis w/hole pin

  1. Apply mp grease to the contact surface of the hole pin and clevis bush.
  2.  connect the clevis to the clutch pedal sub–assy with the hole pin.

    Hint

    : install the hole pin from the right side of the vehicle.

  3.  install the clip to the hole pin.

17. Install clutch pedal spring

18. Install instrument panel sub–assy lower

19. Inspect srs warning light

20. Inspect and adjust clutch pedal sub–assy

Components
...

Clutch master cylinder assy (mtm)
...

Other materials:

Listing the registered cellular phones
Select “List Phone” using .  The list of registered cellular phones will be displayed. ● Connecting the registered cellular phone to the audio system 1 Select the name of the cellular phone to be connected using . 2 Select “Select” using . ● Deleting a registered cellular pho ...

Editing the contact data
For PBAP compatible Bluetooth® phones, this function is available when “Automatic Contact/History Transfer” is set to off. 1 Select “Edit Contact”. 2 Select the desired contact. 3 Select corresponding to the desired name or number. ► For editing the name Follow the steps in “Registering ...

Circuit description
The d squib circuit consists of the airbag sensor assy center, spiral cable sub–assy and horn button assy. It causes the srs to deploy when the srs deployment conditions are satisfied. Dtc b1180/17 is recorded when a short is detected in the d squib circuit (2nd step). Wiring diagram ...

© 2011-2024 Copyright www.tcorolla.net