Toyota Tacoma manuals

Toyota Corolla Repair Manual: Overhaul

1. Remove speedometer drive (mtm) gear

  1. Remove the speedometer drive (mtm) gear from the front differential case.

2. Remove front differential ring gear

  1. Place matchmarks on the front differential ring gear and front differential case.

  1. Remove the 8 bolts. Using a hammer, remove the front differential ring gear.

3. Inspect front differential side gear backlash

  1. Fixing the front differential pinion from the front differential case side. Using a dial indicator, measure the backlash of the front differential side gear.

    Standard backlash:
    0.05 – 0.20 Mm (0.0020 – 0.0079 In.)

If the backlash is not within the specification, install the connect side gear thrust washers.

4. Remove front differential pinion shaft straight pin

  1. Using a chisel and a hammer, loosen the staked part of the front differential case.

  1. Using a pin punch (f 3 mm) and a hammer, remove the front differential pinion shaft straight pin from the front differential case.

5. Remove front differential pinion shaft no.1

  1. Remove the front differential pinion shaft no.1 From the front differential case.

6. Remove front differential side gear

  1. Remove the 2 front differential pinions, 2 front differential pinion thrust washers, 2 front differential side gear thrust washers and 2 front differential side gears from the front differential case.

Hint

: turning the front differential pinion, remove the 2 pinions and side gear.

7. Inspect front differential pinion thrust washer

  1. Using a micrometer, measure the thickness of the front differential pinion thrust washer.

    Minimum thickness: 0.92 Mm (0.0362 In.)

If the clearance is below the minimum, replace the front differential pinion thrust washer.

8. Inspect front differential pinion shaft no.1

  1. Using a micrometer, measure the the outer diameter of the front differential pinion shaft no.1.

    Minimum outer diameter: 16.982 Mm (0.6686 In.)

If the outer diameter is less than the minimum, replace the front differential pinion shaft no.1.

9. Install front differential side gear

  1. Coat the sliding and rotating surface of the 2 front differential side gears with mp grease.
  2.  install the 2 front differential side gear thrust washers to the 2 front differential side gear.

Hint

: install the front differential side gear thrust washer that has the same thickness as the removed one.

  1.  install the 2 front differential side gears, 2 front differential pinions and 2 front differential side gear thrust washers to the front differential case.

Hint

: turning the front differential pinion, install the 2 front differential pinions with front differential case.

10. Install front differential pinion shaft no.1

  1. Coat the rotating surface of the front differential pinion shaft no.1 With gear oil.
  2.  install the front differential pinion shaft no.1 To the front differential case so that the hole for the front differential pinion shaft straight pin is aligned with the hole in the front differential case.

11. Adjust front differential side gear backlash

  1. Fixing the front differential pinion to the front differential case side. Using a dial indicator, measure the front differential side gear backlash.

    Standard backlash:
    0.05 – 0.20 Mm (0.0020 – 0.0079 In.)

If the backlash is out of specification, replace the side gear thrust washer.

Thrust washer thickness:

Hint:

Hint

:

12. Install front differential pinion shaft straight pin

  1. Using a pin punch (f 3 mm) and a hammer, install the front differential pinion shaft straight pin to the front differential case.

  1. Using a chisel and a hammer, stake the front case hole.

13. Install front differential ring gear

  1. Using a heater, heat the front differential ring gear to 90 – 110 c (194.0 – 230.0 F)
  2.  clean the contact surface of the front differential case.

  1. Align the both matchmarks, quickly install the 8 bolts with the front differential ring gear to the front differential case.

    Torque: 77.4 Nvm (789 Kgf·cm, 57 ft·lbf)

14. Install speedometer drive (mtm) gear

  1. Install the speedometer drive (mtm) gear to the front differential case.
Components
...

Shift & select lever shaft assy (c59)
...

Other materials:

Rear door belt moulding assy lh
Replacement Hint: the installation procedures are the removal procedures in reverse order. Use the same procedures for the rh side and lh side. 1. Remove rear armrest assy lh 2. Remove power window regulator switch assy rear (w/ power window) 3. Remove rear door window regulator han ...

On–vehicle inspection
1. Inspect cooling system for leaks Caution: to avoid the danger of being burned, do not remove the radiator cap while the engine and radiator are still hot, as fluid and steam can be blown out under pressure.  fill the radiator with coolant and attach a radiator cap tester.   ...

Inspection procedure
1 Check operation(stop lamp swtich assy) Check that the stop light comes on when the brake pedal is depressed, and turns off when the brake pedal is released. 2 Input signal check See input signal check on page 05–745.  check the indicator light when the brake pedal is ...

© 2011-2024 Copyright www.tcorolla.net