Toyota Tacoma manuals

Toyota Corolla Repair Manual: Mechanical system tests

1. Perform mechanical system tests

  1. Measure the stall speed.

    The object of this test is to check the overall performance of the transaxle and engine by measuring the stall speeds in the d and r positions.

Notice

:

  1.  Chock the 4 wheels.
  2.  Connect an obd ii scan tool or hand–held tester to the dlc3.
  3.  Fully apply the parking brake.
  4. Keep your left foot pressed firmly on the brake pedal.
  5.  Start the engine.
  6.  Shift into the d position. Press all the way down on the accelerator pedal with your right foot.
  7. Quickly read the stall speed at this time.

    Stall speed: 2,550 150 rpm

  8.  do the same test in the r position.

    Stall speed: 2,550 150 rpm

Evaluation:

Problem

Possible cause

(A) stall speed low in d and r positions
  • Engine output may be insufficient
  • stator one–way clutch not operating properly

H

int

: if the value is less than the specified value by 600 rpm or more, the torque converter could be faulty.

(B) stall speed high in d position
  • Line pressure too low
  • forward clutch slipping
  • no. 2 One–way clutch not operating properly
  • u/d one–way clutch not operating properly
(C) stall speed high in r position
  • Line pressure too low
  • direct clutch slipping
  • 1st and reverse brake slipping
  • u/d brake slipping
(D) stall speed high in d and r positions
  • Line pressure too low
  • improper fluid level
  • u/d one–way clutch not operating properly
  1. Measure the time lag.
  1.  When the shift lever is shifted while the engine is idling, there will be a certain time lapse or lag before the shock can be felt. This is used for checking the condition of the direct clutch, forward clutch, and 1st and reverse brake.

Notice

:

  1. Connect an obd ii scan tool or hand–held tester to the dlc3.
  2.  Fully apply the parking brake.
  3.  Start the engine and check idle speed.

    Idle speed: 650 ± 50 rpm (in n position and a/c off)

  4.  shift the shift lever from the n to d position. Using a stop watch, measure the time from when the lever is shifted until the shock is felt.
  5.  Measure the time lag of n " r in the same way.

Time lag:
n d less than 1.2 Seconds n r less than 1.5 Seconds

Evaluation (if n " d time or n " r time lag is longer than specified):

Problem

Possible cause

N d time lag is longer
  • Line pressure too low
  • forward clutch worn
  • u/d one–way clutch not operating properly
N r time lag is longer
  • Line pressure too low
  • direct clutch worn
  • 1st and reverse brake worn
  • u/d one–way clutch not operating properly
Road test
1. Problem symptom confirmation Taking into consideration the results of the customer problem analysis, try to reproduce the symptoms of the trouble. If the problem is that the transaxle does ...

Hydraulic test
1. Perform hydraulic test Measure the line pressure. Notice: Do the test at normal operation atf temperature 50 to 80 °c (122 to 176 °f). The line pressure test should always be carrie ...

Other materials:

Engine coolant
The coolant level is satisfactory if it is between the “F” and “L” lines on the reservoir when the engine is cold. 1 Reservoir cap 2 “F” line 3 “L” line If the level is on or below the “L” line, add coolant up to the “F” line. ■Coolant selection Only use “Toyota Super Long Life Coola ...

Inspection procedure
1 Check door lock When the door does not operate manually, proceed to ”a”.  when the door does not operate via the key, proceed to ”b”. 2 Inspect door lock control switch W/ power window: remove the power window regulator master switch assy.  Inspect the master ...

Shift lock system (atm)
On–vehicle inspection 1. Check shift lock operation  shift the shift lever to p position.  turn the ignition switch to lock.  check that the shift lever cannot be shifted to any other positions other than p.  turn the ignition switch to on, depress the brake pedal a ...

© 2011-2024 Copyright www.tcorolla.net