Toyota Corolla (E120): Inspection procedure

1 Check p squib circuit(airbag sensor assy center – instrument panel passenger airbag assy)

  1. Disconnect the negative (–) terminal cable from the battery, and wait at least for 90 seconds.
  2.  disconnect the connector between the airbag sensor assy center and the instrument panel passenger airbag assy.
  3.  connect the negative (–) terminal cable to the battery, and wait at least for 2 seconds.
  4.  turn the ignition switch to on.
  5.  for the connector (on the instrument panel passenger airbag assy side) between the airbag sensor assy center and the instrument panel passenger airbag assy, measure the voltage between p2+ and body ground.

Ok: voltage: below 1 v

2 Check air bag sensor assy center

2 Check air bag sensor assy center

Sst 09843–18040

  1. Turn the ignition switch to lock.
  2.  disconnect the negative (–) terminal cable from the battery, and wait at least for 90 seconds.
  3.  connect the connector to the airbag sensor assy center.
  4.  using a service wire, connect p2+ and p2– of the connector (on the instrument panel passenger airbag assy side) between the airbag sensor assy center and the instrument panel passenger airbag assy.
  5.  connect the negative (–) terminal cable to the battery, and wait at least for 2 seconds.
  6.  turn the ignition switch to on, and wait at least for 20 seconds.
  7.  clear the dtc stored in memory .
  8.  turn the ignition switch to lock, and wait at least for 20 seconds.
  9.  turn the ignition switch to on, and wait at least for 20 seconds.
  10.  check the dtc .

    Ok: dtc b1188/56 is not output.

Hint

: codes other than code b1188/56 may be output at this time, but they are not relevant to this check.

3 Check p squib

3 Check p squib

Sst 09843–18040

  1. Turn the ignition switch to lock.
  2.  disconnect the negative (–) terminal cable from the battery, and wait at least for 90 seconds.
  3.  connect the instrument panel passenger airbag assy connector.
  4.  connect the negative (–) terminal cable to the battery, and wait at least for 2 seconds.
  5.  turn the ignition switch to on, and wait at least for 20 seconds.
  6.  clear the dtc stored in memory .
  7.  turn the ignition switch to lock, and wait at least for 20 seconds.
  8.  turn the ignition switch to on, and wait at least for 20 seconds.
  9.  check the dtc .

    Ok: dtc b1188/56 is not output.

Hint

: codes other than code b1188/56 may be output at this time, but they are not relevant to this check.

4 Use simulation method to check

4 Use simulation method to check

Replace all srs components including the wire harness

Replace all srs components including the wire harness

    Share this page:

    Other materials:

    Inspection procedure
    1 Check door lock When the door does not operate manually, proceed to ”a”.  when the door does not operate via the key, proceed to ”b”. 2 Inspect door lock control switch W/ power window: remove the power window regulator master switch assy.  Inspect th ...

    Overhaul
    1. Remove roof headlining assy 2. Remove sliding roof glass sub–assy  using a torx wrench (t25), remove the 4 screws the sliding roof glass.  pull the glass upward to remove it. 3. Remove sliding roof weatherstrip 4. Remove sliding roof drive gear sub–assy Notice: ...

    General information
    There are many ecu controlled systems used in the corolla. In general, ecu controlled system are considered to be very intricate and require a high level of technical knowledge and expert skill to troubleshoot. The fact is, however, that if you proceed by inspecting the circuits one by one, ...