Toyota Corolla (E120): Inspection procedure

1 Check d squib circuit(airbag sensor assy center – horn button assy)

  1. Disconnect the negative (–) terminal cable from the battery, and wait at least for 90 seconds.
  2.  disconnect the connectors between the horn button assy and the airbag sensor assy center.
  3.  for the black connector (on the spiral cable sub–assy side) between the horn button assy and the spiral cable sub–assy, measure the resistance between d2+ and d2–.

    Ok: resistance: below 1 Ω

2 Check air bag sensor assy center

2 Check air bag sensor assy center

Sst 09843–18040

  1. Connect the connector to the airbag sensor assy center.
  2.  using a service wire, connect d2+ and d2– of the black connector (on the spiral cable sub–assy side) between the horn button assy and the spiral cable sub–assy.
  3.  connect the negative (–) terminal cable to the battery, and wait at least for 2 seconds.
  4.  turn the ignition switch to on, and wait at least for 20 seconds.
  5.  clear the dtc stored in memory .
  6.  turn the ignition switch to lock, and wait at least for 20 seconds.
  7.  turn the ignition switch to on, and wait at least for 20 seconds.
  8.  check the dtc .

    Ok: dtc b1181/18 is not output.

Hint

: codes other than code b1181/18 may be output at this time, but they are not relevant to this check.

3 Check d squib

3 Check d squib

Sst 09843–18040

  1. Turn the ignition switch to lock.
  2.  disconnect the negative (–) terminal cable from the battery, and wait at least for 90 seconds.
  3.  connect the horn button assy connectors.
  4.  connect the negative (–) terminal cable to the battery, and wait at least for 2 seconds.
  5.  turn the ignition switch to on, and wait at least for 20 seconds.
  6.  clear the dtc stored in memory .
  7.  turn the ignition switch to lock, and wait at least for 20 seconds.
  8.  turn the ignition switch to on, and wait at least for 20 seconds.
  9.  check the dtc .

    Ok: dtc b1181/18 is not output.

Hint

: codes other than code b1181/18 may be output at this time, but they are not relevant to this check.

Use simulation method to check

Use simulation method to check

4 Check instrument panel wire(airbag sensor assy center – spiral cable sub–assy)

  1. Disconnect the connector of the instrument panel wire.
  2.  for the connector (on the spiral cable sub–assy side) between the airbag sensor assy center and the spiral cable sub–assy, measure the resistance between d2+ and d2–.

    Ok: resistance: below 1 w

5 Check spiral cable sub–assy

5 Check spiral cable sub–assy

  1. For the black connector (on the spiral cable sub–assy side) between the horn button assy and the spiral cable sub–assy, measure the resistance between d2+ and d2–.

    Ok: resistance: below 1 Ω

Use simulation method to check

Use simulation method to check

    Share this page:

    Other materials:

    When the contact is empty
    You can transfer the phone numbers in a Bluetooth® phone to the system. Operation methods differ between PBAP (Phone Book Access Profile) compatible and PBAP incompatible Bluetooth® phones. If the cellular phone does not support either PBAP or OPP (Object Push Profile) service, you cannot tra ...

    Problem symptoms table
    The suspected circuits or parts for each problem symptom are shown in the table below. Use this table to troubleshoot the problem when a normal code is displayed in the diagnostic trouble code chart but the problem is still occurring. Numbers in the table indicate the order in which the circ ...

    Replacement
    Hint: installation is in the reverse order of the removal. But the installation is indicated only when it has a point. 1. Remove luggage compartment door cover 2. Remove rear spoiler  remove the 2 screws.  disconnect the wire harness connector.  put protective tape. &nb ...