Toyota Corolla (E120): Inspection procedure

1 Check front airbag sensor (rh) circuit (to b+)(airbag sensor assy center – airbag front rh sensor)

  1. Disconnect the negative (–) terminal cable from the battery, and wait at least for 90 seconds.
  2.  disconnect the connectors between the airbag front rh sensor and the airbag sensor assy center.
  3.  connect the negative (–) terminal cable to the battery, and wait at least for 2 seconds.
  4.  turn the ignition switch to on.
  5.  for the connector (on the airbag sensor assy center side) between the airbag front rh sensor and the airbag sensor assy center, measure the voltage between body ground and each of +sr and –sr.

    Ok: voltage: below 1 v

2 Check front airbag sensor (rh) circuit (to ground)(airbag sensor

2 Check front airbag sensor (rh) circuit (to ground)(airbag sensor assy – airbag front rh sensor)

  1. Turn the ignition switch to lock.
  2.  disconnect the negative (–) terminal cable from the battery, and wait at least for 90 seconds.
  3.  for the connector (on the airbag sensor assy center side) between the airbag front rh sensor and the airbag sensor assy center, measure the resistance between body ground and each of +sr and –sr.

    Ok: resistance: 1 mΩ or higher

3 Check front airbag sensor (rh) circuit(open)(airbag sensor assy

3 Check front airbag sensor (rh) circuit(open)(airbag sensor assy center – airbag front rh sensor)

Sst 09843–18040

  1. Using a service wire, connect +sr and –sr of the connector (on the airbag front rh sensor side) between the airbag front rh sensor and the airbag sensor assy center.
  2.  for the connector (on the airbag sensor assy center side) between the airbag front rh sensor and the airbag sensor assy center, measure the resistance between +sr and –sr.

    Ok: resistance: below 1 Ω

4 Inspect air bag front rh sensor

4 Inspect air bag front rh sensor

  1. For the connector of the airbag front rh sensor, measure the resistance between +sr and –sr.

    Ok: resistance: 820 Ω

5 Check air bag sensor assy center

5 Check air bag sensor assy center

Sst 09843–18040

  1. Disconnect the negative (–) terminal cable from the battery, and wait at least for 90 seconds.
  2.  connect the airbag front rh sensor connector and airbag sensor assy center connector.
  3.  connect the negative (–) terminal cable to the battery, and wait at least for 2 seconds.
  4.  turn the ignition switch to on, and wait at least for 20 seconds.
  5.  clear the dtc stored in memory .
  6.  turn the ignition switch to lock, and wait at least for 20 seconds.
  7.  turn the ignition switch to on, and wait at least for 20 seconds.
  8.  check the dtc .

    Ok: dtc b1156/b1157/15 is not output.

Hint

: codes other than code b1156/b1157/15 may be output at this time, but they are not relevant to this check.

Use simulation method to check

Use simulation method to check

6 Check engine room main wire harness (to b+)(connector – airbag front rh sensor)

  1. Turn the ignition switch to lock.
  2.  disconnect the negative (–) terminal cable from the battery, and wait at least for 90 seconds.
  3.  disconnect the connector between the engine room main wire and the instrument panel wire.
  4.  connect the negative (–) terminal cable to the battery, and wait at least for 2 seconds.
  5.  turn the ignition switch to on.
  6.  for the engine room main wire connector (on the airbag sensor assy center side) between the airbag sensor assy center and the airbag front rh sensor, measure the voltage between body ground and each of +sr and –sr.

    Ok: voltage: below 1 v

Repair or replace instrument panel wire

Repair or replace instrument panel wire

7 Check engine room main wire harness (to ground)(connector – airbag front rh sensor)

  1. Disconnect the connectors between the engine room main wire and the instrument panel wire.
  2.  for the engine room main wire connector (on the airbag sensor assy center side) between the airbag sensor assy center and the airbag front rh sensor, measure the resistance between body ground and each of +sr and –sr.

    Ok: resistance: 1 mΩ or higher

Repair or replace instrument panel wire

Repair or replace instrument panel wire

8 Check engine room main wire harness(open)(connector – airbag front rh sensor)

Sst 09843–18040

  1. Disconnect the connectors between the engine room main wire and the instrument panel wire.
  2.  using a service wire, connect +sr and –sr of the engine room main wire connector (on the airbag front rh sensor side) between the airbag sensor assy center and the airbag front rh sensor.
  3.  for the engine room main wire connector (on the airbag sensor assy center side) between the airbag sensor assy center and the airbag front rh sensor, measure the resistance between the +sr and –sr.

    Ok: resistance: below 1 Ω

Repair or replace instrument panel wire

Repair or replace instrument panel wire

    Share this page:

    Other materials:

    If your vehicle overheats
    The following may indicate that your vehicle is overheating. ● Vehicles without a multi-information display: The high engine coolant temperature warning light  comes on or a loss of power is experienced. Vehicles with a multi-information display: The engine coolant temperature gauge&n ...

    Key information
    Keys The following keys are provided with the vehicle. ►  Vehicles without a smart key system (type A) 1 Keys 2 Key number plate ► Vehicles without a smart key system (type B) 1 Keys Operating the wireless remote control function 2 Key number plate ► Vehicles ...

    Precaution
    1. Notices when checking  power door lock/unlock function: the wireless remote control function operates only when the following 3 conditions are met.  No key is inserted into the ignition key cylinder.  All the doors are closed. However, doors can be unlocked even wh ...