Toyota Corolla (E120): Inspection procedure

1 Check side air bag sensor assy rh

Sst 09843–18040

  1. Connect the negative (–) terminal cable to the battery, and wait at least for 2 seconds.
  2.  turn the ignition switch to on, and wait at least for 20 seconds.
  3.  clear the dtc stored in memory .
  4.  turn the ignition switch to lock, and wait at least for 20 seconds.
  5.  turn the ignition switch to on, and wait at least for 20 seconds.
  6.  check the dtc .

    Ok: dtc b1140/32 is not output.

Hint

: codes other than code b1140/32 may be output at this time, but they are not relevant to this check.

2 Check airbag sensor assy center connector

2 Check airbag sensor assy center connector

  1. Turn the ignition switch to lock.
  2.  disconnect the negative (–) terminal cable from the battery, and wait at least for 90 seconds.
  3.  check that the connectors is properly connected to the airbag sensor assy center.

3 Check side airbag sensor assy connector

3 Check side airbag sensor assy connector

  1. Check that the connector is properly connected to the side airbag sensor assy (rh).

4 Check side airbag sensor assy(rh) circuit(open)(airbag sensor

4 Check side airbag sensor assy(rh) circuit(open)(airbag sensor assy center – side airbag sensor assy rh)

Sst 09843–18040

  1. Disconnect the connectors between the airbag sensor assy center and the side airbag sensor assy rh.
  2.  using a service wire, connect vupr and esr, and fsr and ssr– of the connector (on the side airbag sensor assy side) between the airbag sensor assy center and the side airbag sensor assy (rh).
  3.  for the connector (on the airbag sensor assy center side) between the side airbag sensor assy rh and the airbag sensor assy center, measure the resistance between vupr and esr, and between fsr and ssr–.

    Ok: resistance: below 1 Ω

5 Check side airbag sensor assy(rh) circuit(to ground)(airbag

5 Check side airbag sensor assy(rh) circuit(to ground)(airbag sensor assy center – side airbag sensor assy rh)

  1. Disconnect the connection between vupr and esr, and between fsr and ssr–.
  2.  for the connector (on the airbag sensor assy center side) between the airbag sensor assy center and the side airbag sensor assy (rh), measure the resistance between each terminal of vupr, ssr– and fsr, and body ground.

    Ok: resistance: 1mΩ or higher

6 Check side airbag sensor assy(rh) circuit(airbag sensor assy

6 Check side airbag sensor assy(rh) circuit(airbag sensor assy center – side airbag sensor assy rh)

  1. For the connector (on the airbag sensor assy center side) between the airbag sensor assy center and the side airbag sensor assy (rh), measure the resistance between vupr and esr, and between fsr and ssr–.

    Ok: resistance: 1mΩ or higher

7 Check side airbag sensor assy(rh) circuit(to b+)(airbag sensor

7 Check side airbag sensor assy(rh) circuit(to b+)(airbag sensor assy center – aide airbag sensor assy rh)

  1. Connect the negative (–) terminal cable to the battery, and wait at least for 2 seconds.
  2.  turn the ignition switch to on.
  3.  for the connector (on the airbag sensor assy center side) between the airbag sensor assy center and the side airbag sensor assy (rh), measure the voltage between each terminal of vupr, ssr– and fsr, and body ground.

    Ok: voltage: below 1 v

8 Check side air bag sensor assy rh

8 Check side air bag sensor assy rh

Sst 09843–18040

  1. Turn the ignition switch to lock.
  2.  disconnect the negative (–) terminal cable from the battery, and wait at least for 90 seconds.
  3.  connect the airbag sensor assy center connector.
  4.  interchange the side airbag sensor assy (rh) and lh and connect the connectors to them.
  5.  connect the negative (–) terminal cable to the battery, and wait at least for 2 seconds
  6.  turn the ignition switch to on, and wait at least for 20 seconds.
  7.  clear the dtc stored in memory .
  8.  turn the ignition switch to lock, and wait at least for 20 seconds.
  9.  turn the ignition switch to on, and wait at least for 20 seconds.
  10.  check the dtc .

    Ok: (a): dtc b1140/32 is not output.

    (B): dtc b1141/33 is not output.

9 Use simulation method to check

9 Use simulation method to check

Replace all srs components including the wire harness

Replace all srs components including the wire harness

    Share this page:

    Other materials:

    Vehicle load limits
    Vehicle load limits include total load capacity, seating capacity, towing capacity and cargo capacity. ◆ Total load capacity (vehicle capacity weight): Total load capacity means the combined weight of occupants, cargo and luggage. ◆ Seating capacity: 5 occupants (Front 2, Rear 3) S ...

    If the engine will not start
    If the engine will not start even though correct starting procedures are being followed , consider each of the following points: The engine will not start even though the starter motor operates normally. One of the following may be the cause of the problem: ● There may not be sufficient f ...

    How to proceed with troubleshooting
    The hand–held tester can be used at step 3, 4, 6, 9. 1 Vehicle brought to workshop 2 Customer problem analysis 3 Connect the obd ii scan tool or hand–held tester to dlc3 4 Check and clear dtc and freeze frame data 5 Visual inspection 6 Setting the check mode diagnosis 7 Proble ...