Toyota Corolla (E120): Inspection procedure

1 Check side squib(rh) circuit(airbag sensor assy center – front seat airbag assy rh)

  1. Disconnect the negative (–) terminal cable from the battery, and wait at least for 90 seconds.
  2.  disconnect the connectors between the airbag sensor assy center and the front seat airbag assy (rh).
  3.  connect the negative (–) terminal cable to the battery, and wait at least for 2 seconds.
  4.  turn the ignition switch to on.
  5. for the connector (on the front seat airbag assy side) between the airbag sensor assy center and the front seat airbag assy (rh), measure the voltage between sfr+ and body ground.

    Ok: voltage: below 1 v

2 Check air bag sensor assy center

2 Check air bag sensor assy center

Sst 09843–18040

  1. Turn the ignition switch to lock.
  2.  disconnect the negative (–) terminal cable from the battery, and wait at least for 90 seconds.
  3.  connect the connector to the airbag sensor assy center.
  4.  using a service wire, connect sfr+ and sfr– of the connector (on the front front seat airbag assy side) between the airbag sensor assy center and the front seat airbag assy (rh).
  5.  connect the negative (–) terminal cable to the battery, and wait at least for 2 seconds.
  6.  turn the ignition switch to on, and wait at least for 20 seconds.
  7.  clear the dtc stored in memory .
  8.  turn the ignition switch to lock, and wait at least for 20 seconds.
  9.  turn the ignition switch to on, and wait at least for 20 seconds.
  10.  check the dtc .

    Ok: dtc b0113/42 is not output.

Hint

: codes other than code b0113/42 may be output at this time, but they are not relevant to this check.

3 Check side squib(rh)

3 Check side squib(rh)

Sst 09843–18040

  1. Turn the ignition switch to lock.
  2.  disconnect the negative (–) terminal cable from the battery, and wait at least for 90 seconds.
  3.  connect the front seat airbag assy (rh) connector.
  4.  connect the negative (–) terminal cable to the battery, and wait at least for 2 seconds.
  5.  turn the ignition switch to on, and wait at least for 20 seconds.
  6.  clear the dtc stored in memory .
  7.  turn the ignition switch to lock, and wait at least for 20 seconds.
  8.  turn the ignition switch to on, and wait at least for 20 seconds.
  9.  check the dtc .

    Ok: dtc b0113/42 is not output.

Hint

: codes other than code b0113/42 may be output at this time, but they are not relevant to this check.

4 Use simulation method to check

4 Use simulation method to check

Replace all srs components including the wire harness

Replace all srs components including the wire harness

    Share this page:

    Other materials:

    Overhaul
    1. Remove bench type rear seat cushion assy Disengage the 2 clamps, and then remove the seat cushion. 2. Remove separate type rear seat back assy  lean the seat back forward.  remove the 2 clips.  remove the 2 bolts and seat back lh. employ the same manner describ ...

    Circuit description
    The variable valve timing (vvt) system includes the ecm, the oil control valve (ocv) and the vvt controller. The ecm sends a target ”duty–cycle” control signal to the ocv. This control signal, applied to the ocv, regulates the oil pressure supplied to the vvt controller. Camshaft timin ...

    Transmitter battery
    Replacement 1. Replace transmitter battery Notice: special caution should be taken for handling each component as they are precision electronic components. Using a screwdriver, pry out the transmitter case. Notice: do not forcibly pry out the case. Hint: tape the screwdriver tip ...