Toyota Tacoma manuals

Toyota Corolla Repair Manual: Inspection procedure

1 Check side squib(rh) circuit(airbag sensor assy center – front seat airbag assy rh)

  1. Disconnect the negative (–) terminal cable from the battery, and wait at least for 90 seconds.
  2. disconnect the connectors between the front seat airbag assy (rh) and the airbag sensor assy center.
  3.  release the airbag activation prevention mechanism of the connector (on the airbag sensor assy center side) between the airbag sensor assy center and the front seat airbag assy (rh) .
  4.  for the connector (on the front seat airbag assy side) between the airbag sensor assy center and the front seat airbag assy (rh), measure the resistance between sfr+ and sfr–.

    Ok: resistance: 1 mw or higher

2 Check air bag sensor assy center

2 Check air bag sensor assy center

Sst 09843–18040

  1. Connect the the connector to the airbag sensor assy center.
  2.  connect the negative (–) terminal cable to the battery, and wait at least for 2 seconds.
  3.  turn the ignition switch to on, and wait at least for 20 seconds.
  4.  clear the dtc stored in memory .
  5.  turn the ignition switch to lock, and wait at least for 20 seconds.
  6.  turn the ignition switch to on, and wait at least for 20 seconds.
  7.  check the dtc .

    Ok: dtc b0110/43 is not output.

Hint

: codes other than code b0110/43 may be output at this time, but they are not relevant to this check.

3 Check side squib(rh)

3 Check side squib(rh)

Sst 09843–18040

  1. Turn the ignition switch to lock.
  2.  disconnect the negative (–) terminal cable from the battery, and wait at least for 90 seconds.
  3.  connect the front seat airbag assy (rh) connector.
  4.  connect the negative (–) terminal cable to the battery, and wait at least for 2 seconds.
  5. turn the ignition switch to on, and wait at least for 20 seconds.
  6.  clear the dtc stored in memory .
  7.  turn the ignition switch to lock, and wait at least for 20 seconds.
  8.  turn the ignition switch to on, and wait at least for 20 seconds.
  9.  check the dtc .

    Ok: dtc b0110/43 is not output.

Hint

: codes other than code b0110/43 may be output at this time, but they are not relevant to this check.

Use simulation method to check

Use simulation method to check

Circuit description
The side squib (rh) circuit consists of the airbag sensor assy center and front seat airbag assy (rh). It causes the srs to deploy when the srs deployment conditions are satisfied. Dtc b0110/4 ...

Open in side squib (rh) circuit
Dtc b0111/44 open in side squib (rh) circuit ...

Other materials:

Inspection procedure
1 Check p squib circuit(airbag sensor assy center – instrument panel passenger airbag assy) Disconnect the negative (–) terminal cable from the battery, and wait at least for 90 seconds.  disconnect the connector between the airbag sensor assy center and the instrument panel pass ...

Overhaul
1. Precaution 2. Disconnect battery negative terminal 3. Inspect place front wheels facing straight ahead 4. Remove horn button assy Notice: if the airbag connector is disconnected with the ignition switch being at on, dtcs will be recorded.  using a torx socket wrench, loosen the ...

Stopping
► Automatic transmission or continuously variable transmission 1 With the shift lever in D, depress the brake pedal. 2 If necessary, set the parking brake. If the vehicle is to be stopped for an extended period of time, shift the shift lever to P or N. (, 174, 176) ►  Manual ...

© 2011-2024 Copyright www.tcorolla.net