Toyota Corolla (E120): Inspection procedure

1 Check p squib circuit(airbag sensor assy center – instrument panel passenger airbag assy)

  1. Disconnect the negative (–) terminal cable from the battery, and wait at least for 90 seconds.
  2.  disconnect the connectors between the airbag sensor assy center and the instrument panel passenger airbag assy.
  3.  connect the negative (–) terminal cable to the battery, and wait at least for 2 seconds.
  4.  turn the ignition switch to on.
  5.  for the connector (on the instrument panel passenger airbag assy side) between the airbag sensor assy center and the instrument panel passenger airbag assy, measure the voltage between p+ and body ground.

    Ok: voltage: below 1 v

2 Check air bag sensor assy center

2 Check air bag sensor assy center

Sst 09843–18040

  1. Turn the ignition switch to lock.
  2.  disconnect the negative (–) terminal cable from the battery, and wait at least for 90 seconds.
  3.  connect the connector to the airbag sensor assy center.
  4.  using a service wire, connect p+ and p– of the connector (on the instrument panel passenger airbag assy side) between the airbag sensor assy center and the instrument panel passenger airbag assy.
  5.  connect the negative (–) terminal cable to the battery, and wait at least for 2 seconds.
  6.  turn the ignition switch to on, and wait at least for 20 seconds.
  7.  clear the dtc stored in memory .
  8.  turn the ignition switch to lock, and wait at least for 20 seconds.
  9.  turn the ignition switch to on, and wait at least for 20 seconds.
  10.  check the dtc .

    Ok: dtc b0108/52 is not output.

Hint

: codes other than code b0108/52 may be output at this time, but they are not relevant to this check.

3 Check p squib

3 Check p squib

Sst 09843–18040

  1. Turn the ignition switch to lock.
  2.  disconnect the negative (–) terminal cable from the battery, and wait at least for 90 seconds.
  3.  connect the instrument panel passenger airbag assy connector.
  4.  connect the negative (–) terminal cable to the battery, and wait at least for 2 seconds.
  5. turn the ignition switch to on, and wait at least for 20 seconds.
  6.  clear the dtc stored in memory .
  7. turn the ignition switch to lock, and wait at least for 20 seconds.
  8. turn the ignition switch to on, and wait at least for 20 seconds.
  9.  check the dtc .

    Ok: dtc b0108/52 is not output.

Hint

: codes other than code b0108/52 may be output at this time, but they are not relevant to this check.

4 Use simulation method to check

4 Use simulation method to check

Replace all srs components including the wire harness

Replace all srs components including the wire harness

    Share this page:

    Other materials:

    Child restraint system fixed with an ISOFIX lower anchorage (for Puerto Rico)
    ■ ISOFIX lower anchorages (ISOFIX child restraint system) Lower anchorages are provided for the outboard rear seats. (Marks displaying the location of the anchorages are attached to the seats.) ■ When installing in the rear outboard seats Install the child restraint system in accordance to the ...

    Disposal
    Hint: when scrapping vehicle equipped with an srs or disposing of a horn button assy, always first deploy the airbag in accordance with the procedure described below. If any abnormality occurs in the airbag deployment, contact the service dept. Of toyota motor sales, u.S.A., Inc. Caution: ...

    Inspection procedure
    1 Inspect fuse(ecu–ig fuse) Remove ecu–ig fuse from the instrument panel j/b.  check continuity of ecu–ig fuse. Ok: continuity 2 Inspect battery Ok: voltage: 10 – 14 v 3 Inspect skid control ecu connector(ig1 terminal voltage) In case of using hand–held te ...