Toyota Tacoma manuals

Toyota Corolla Repair Manual: Inspection procedure

1 Check d squib circuit(airbag sensor assy center – horn button assy)

  1. Disconnect the negative (–) terminal cable from the battery, and wait at least for 90 seconds.
  2.  disconnect the connectors between the airbag sensor assy center and the horn button assy.
  3.  for the orange connector (on the spiral cable sub–assy side) between the horn button assy and the spiral cable sub–assy, measure the resistance between d+ and body ground.

    Ok: resistance: 1 mw or higher

2 Check air bag sensor assy center

2 Check air bag sensor assy center

Sst 09843–18040

  1. Connect the connector to the airbag sensor assy center.
  2.  using a service wire, connect d+ and d– of the orange connector (on the spiral cable sub–assy side) between the horn button assy and the spiral cable sub–assy.
  3.  connect the negative (–) terminal cable to the battery, and wait at least for 2 seconds.
  4.  turn the ignition switch to on, and wait t least for 20 seconds.
  5.  clear the dtc stored in memory .
  6.  turn the ignition switch to lock, and wait at least for 20 seconds.
  7.  turn the ignition switch to on, and wait at least for 20 seconds.
  8.  check the dtc .

    Ok: dtc b0102/11 is not output.

Hint

: codes other than code b0102/11 may be output at this time, but they are not relevant to this check.

3 Check d squib

3 Check d squib

Sst 09843–18040

  1. Turn the ignition switch to lock.
  2.  disconnect the negative (–) terminal cable from the battery, and wait at least for 90 seconds.
  3.  connect the horn button assy connectors.
  4.  connect the negative (–) terminal cable to the battery, and wait at least for 2 seconds.
  5.  turn the ignition switch to on, and wait at least for 20 seconds.
  6. clear the dtc stored in memory .
  7.  turn the ignition switch to lock, and wait at least for 20 seconds.
  8.  turn the ignition switch to on, and wait at least for 20 seconds.
  9.  check the dtc .

    Ok: dtc b0102/11 is not output.

Hint

: codes other than code b0102/11 may be output at this time, but they are not relevant to this check.

4 Use simulation method to check

4 Use simulation method to check

Replace all srs components including the wire harness

Replace all srs components including the wire harness

5 Check instrument panel wire(airbag sensor assy center – spiral cable sub–assy)

  1. Disconnect the connector of the instrument panel wire.
  2.  for the connector (on the spiral cable sub–assy side) between the airbag sensor assy center and the spiral cable sub–assy, measure the resistance between d+ and body ground.

    Ok: resistance: 1 mΩ or higher

6 Check spiral cable sub–assy

6 Check spiral cable sub–assy

  1. For the orange connector (on the spiral cable sub–assy side) between the horn button assy and the spiral cable sub–assy, measure the resistance between d+ and body ground.

    Ok: resistance: 1 mΩ or higher

7 Use simulation method to check

7 Use simulation method to check

Replace all srs components including the wire harness

Replace all srs components including the wire harness

Circuit description
The d squib circuit consists of the airbag sensor assy center, spiral cable sub–assy and horn button assy. It causes the srs to deploy when the srs deployment conditions are satisfied. Dtc b01 ...

Short in d squib circuit (to b+)
Dtc b0103/12 short in d squib circuit (to b+) ...

Other materials:

Description
1. Radio wave band The radio wave bands used in radio broadcasting are as follows: Lf: low frequency mf: medium frequency hf: high frequency vhf: very high frequency 2. Service area There are great differences in the size of the service area for am and fm broadcasting. Sometimes ...

Pre–check
1. Selecting compass display mode  the compass switch allows you to select the display or non–display mode of the compass. 2. Setting zone  deviation between the ”magnetic north” and ”actual north” differs depending on the location. Therefore, adjustment of the magnetism ...

Inspection procedure
1 Check side air bag sensor assy lh Sst 09843–18040 Connect the negative (–) terminal cable to the battery, and wait at least for 2 seconds.  turn the ignition switch to on, and wait at least for 20 seconds.  clear the dtc stored in memory .  turn the ignition switch ...

© 2011-2024 Copyright www.tcorolla.net