Toyota Corolla (E120): Inspection procedure

1 Check d squib circuit(airbag sensor assy center – horn button assy)

  1. Disconnect the negative (–) terminal cable from the battery, and wait at least for 90 seconds.
  2.  disconnect the connectors between the horn button assy and the airbag sensor assy center.
  3.  for the orange connector (on the spiral cable sub–assy side) between the horn button assy and the spiral cable sub–assy, measure the resistance between d+ and d–.

    Ok: resistance: below 1 Ω

2 Check air bag sensor assy center

2 Check air bag sensor assy center

Sst 09843–18040

  1. Connect the connector to the airbag sensor assy center.
  2.  using a service wire, connect d+ and d– of the orange connector (on the spiral cable sub–assy side) between the horn button assy and the spiral cable sub–assy.
  3.  connect the negative (–) terminal cable to the battery, and wait at least for 2 seconds.
  4.  turn the ignition switch to on, and wait at least for 20 seconds.
  5.  clear the dtc stored in memory .
  6.  turn the ignition switch to lock, and wait at least for 20 seconds.
  7.  turn the ignition switch to on, and wait at least for 20 seconds.
  8.  check the dtc .

    Ok: dtc b0101/14 is not output.

Hint

: codes other than code b0101/14 may be output at this time, but they are not relevant to this check.

3 Check d squib

3 Check d squib

Sst 09843–18040

  1. Turn the ignition switch to lock.
  2.  disconnect the negative (–) terminal cable from the battery, and wait at least for 90 seconds.
  3.  connect the horn button assy connector.
  4.  connect the negative (–) terminal cable to the battery, and wait at least for 2 seconds.
  5.  turn the ignition switch to on, and wait at least for 20 seconds.
  6.  clear the dtc stored in memory .
  7.  turn the ignition switch to lock, and wait at least for 20 seconds.
  8.  turn the ignition switch to on, and wait at least for 20 seconds.
  9.  check the dtc .

    Ok: dtc b0101/14 is not output.

Hint

: codes other than code b0101/14 may be output at this time, but they are not relevant to this check.

Use simulation method to c

Use simulation method to c

4 Check instrument panel wire(airbag sensor assy center – spiral cable sub–assy)

  1. Disconnect the connector of the instrument panel wire.
  2. for the connector (on the spiral cable sub–assy side) between the airbag sensor assy center and the spiral cable sub–assy, measure the resistance between d+ and d–.

    Ok: resistance: below 1 Ω

5 Check spiral cable sub–assy

5 Check spiral cable sub–assy

  1. For the orange connector (on the spiral cable sub–assy side) between the horn button assy and the spiral cable sub–assy, measure the resistance between d+ and d–.

    Ok: resistance: below 1 Ω

Use simulation method to check

Use simulation method to check

    Share this page:

    Other materials:

    Luggage door hinge torsion bar rh
    Replacement Hint: installation is in the reverse order of the removal. But the installation is indicated only when it has a point. In the lh side, work in the same procedure as in the rh side. Since the removal of the torsion bar will cause no tension, operation of opening and closi ...

    Tire size
    ■ Typical tire size information The illustration indicates typical tire size. 1 Tire use (P = Passenger car, T = Temporary use) 2 Section width (millimeters) 3 Aspect ratio (tire height to section width) 4 Tire construction code (R = Radial, D = Diagonal) 5 Wheel diameter (inches) 6 Loa ...

    Confirmation driving pattern
    Connect the hand–held tester or the obd ii scan tool to the dlc3.  record dtcs and the freeze frame data.  set the check mode using the hand–held tester .  read the value on the misfire counter for each cylinder when idling. If the value is displayed on the misfire c ...