Toyota Corolla (E120): Inspection procedure

Hint

:

  • if different dtcs related to different systems that have terminal e2 as the ground terminal are output simultaneously, terminal e2 may be open.
  • Read freeze frame data using the hand-held tester or the obd ii scan tool. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, it is useful for determining whether the vehicle was running or stopped, the engine was warmed up or not, the air–fuel ratio was lean or rich, etc. At the time of the malfunction.

Hand–held tester:

1 Read value of hand–held tester(throttle valve opening percentage)

  1. Connect the hand–held tester to the dlc3.
  2.  turn the ignition switch on.
  3.  select the item ”diagnosis / enhanced obd ii / data list / etcs / throttle pos” and read its value displayed on the hand–held tester.

Result:

2 Inspect throttle position sensor

2 Inspect throttle position sensor

  1. Disconnect the t1 throttle position sensor connector.
  2.  measure the resistance between the terminals of the throttle position sensor.

Standard

  1. Reconnect the throttle position sensor connector.

3 Check harness and connector(ecm – throttle position sensor)

3 Check harness and connector(ecm – throttle position sensor)

  1. Disconnect the e3 ecm connector.
  2.  measure the resistance between the terminals of the e3 ecm connector.

Standard:

  1. Check the resistance between the terminals of the e3 ecm connector.

Standard (check for short):

  1. Reconnect the ecm connector.

Replace ecm

Replace ecm

4 Inspect throttle position sensor

  1. Disconnect the t1 throttle position sensor connector.
  2.  measure the resistance between the terminals of the throttle position sensor.

Standard:

  1. Reconnect the throttle position sensor connector.

5 Check harness and connector(ecm – throttle position sensor)

5 Check harness and connector(ecm – throttle position sensor)

  1. Disconnect the e3 ecm connector.
  2.  disconnect the t1 throttle position sensor connector.
  3.  check the resistance between the wire harness side connectors.

Standard (check for open):

Standard (check for short):

Standard (check for short):

  1. Reconnect the throttle position sensor connector.
  2.  reconnect the ecm connector.

Replace ecm

Replace ecm

Obd ii scan tool (excluding hand–held tester):

1 Inspect throttle position sensor

  1. Disconnect the t1 throttle position sensor connector.
  2.  measure the resistance between the terminals of the throttle position sensor.

Standard:

  1. Reconnect the throttle position sensor connector.

2 Check harness and connector(throttle position sensor – ecm)

2 Check harness and connector(throttle position sensor – ecm)

  1. Disconnect the e3 ecm connector.
  2. measure the resistance between the terminals of the e3 ecm connector.

Standard:

  1. Check the resistance between the terminals of the e3 ecm connector.

Standard (check for short):

  1. Reconnect the ecm connector.

Throttle/pedal position

    Share this page:

    Other materials:

    Body rocker panel moulding lh
    Replacement Hint: use the same procedures for the rh side and lh side. 1. Remove body rocker panel moulding lh Remove the 8 retainers.  using a screwdriver, remove the moulding. Hint: tape the screwdriver tip before use.  remove the 7 clips from the moulding. 2. Insta ...

    Tape is tangled due to incorrect tape speed or auto–reverse malfunction
    Inspection procedure 1 Check for any foreign object Check for any foreign object. Check that no foreign material and troubles are detected in the radio receiver assembly cassette tape player. Standard: no foreign material and trouble detected. 2 Replace cassette tape with an ...

    Power door lock control system
    Symptom Suspected area All doors are not operated by driver’s door key cylinder interlocked with key Door lock control switch Front door lock assy lh  Wire harness Integration relay Key confinement prevention function does ...