Toyota Corolla (E120): Inspection procedure

Hint

: read freeze frame data using the hand–held tester or the obd ii scan tool. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, it is useful for determining whether the vehicle was running or stopped, the engine was warmed up or not, the air–fuel ratio was lean or rich, etc. At the time of the malfunction.

Hand–held tester

1 Perform active test by hand–held tester(operate ocv)

  1. Connect the hand–held tester to the dlc3.
  2.  start the engine and warm it up.
  3.  turn the ignition switch on and push the hand–held tester main switch on.
  4.  select the item ”diagnosis / enhanced obd ii / active test / vvt ctrl b1”.
  5.  check the engine speed when operating the oil control valve (ocv) by the hand–held tester.

Standard:

2 Inspect camshaft timing oil control valve assy(ocv)

2 Inspect camshaft timing oil control valve assy(ocv)

3 Inspect ecm(ocv signal)

3 Inspect ecm(ocv signal)

  1. Inspection using the oscilloscope.
  2. during idling, check the waveform between the terminals of the e3 ecm connector.

Standard:

4 Check harness and connector(camshaft timing oil control valve

4 Check harness and connector(camshaft timing oil control valve (ocv) – ecm)

  1. Disconnect the c2 camshaft timing oil control valve connector.
  2.  disconnect the e3 ecm connector.
  3.  check the resistance between the wire harness side connectors.

Standard (check for open):

Standard (check for open):

Standard (check for short):

Standard (check for short):

  1. Reconnect the camshaft timing oil control valve connector.
  2.  reconnect the ecm connector.

Check for intermittent problems

Check for intermittent problems

Obdii scan tool (excluding hand–held tester):

1 Inspect camshaft timing oil control valve assy(operate ocv)

  1. Disconnect the c2 camshaft timing oil control valve connector.
  2.  apply positive battery voltage between the terminals of the camshaft timing oil control valve.
  3.  check the engine speed.

    Standard

    : engine speed is rough idle or engine is stalled.

  4.  reconnect the camshaft timing oil control valve connector.

2 Inspect ecm(ocv signal)

2 Inspect ecm(ocv signal)

  1. Inspection using the oscilloscope.
  2.  during idling, check the waveform between the terminals of the e3 ecm connector.

Standard:

3 Check harness and connector(camshaft timing oil control valve

3 Check harness and connector(camshaft timing oil control valve (ocv) – ecm)

  1. Disconnect the c2 camshaft timing oil control valve connector.
  2.  disconnect the e3 ecm connector.
  3.  check the resistance between the wire harness side connectors.

Standard (check for open):

Standard (check for open):

Standard (check for short):

Standard (check for short):

  1. Reconnect the camshaft timing oil control valve connector.
  2. reconnect the ecm connector.

Check for intermittent problems

Check for intermittent problems

    Share this page:

    Other materials:

    If the engine will not start
    If the engine will not start even though correct starting procedures are being followed , consider each of the following points: The engine will not start even though the starter motor operates normally. One of the following may be the cause of the problem: ● There may not be sufficient f ...

    Repair
    1. Steering off center repair procedure Inspect steering wheel off center.  Apply masking tape on the top center of the steering wheel and steering column upper cover.  Driving the vehicle on a straight line for 100 meters at a constant speed of 35 mph (56 km/h), and ho ...

    Inspection procedure
    1 Check door lock 2 Check wire harness (tvip ecu door lock) Disconnect the tvip ecu and door lock connectors.  check the continuity between the terminals of the tvip ecu and door lock connectors, as shown in the illustration and table. Standard: 3 Check wire harness ...