Toyota Tacoma manuals

Toyota Corolla Repair Manual: Front suspension arm sub–assy lower no.1 Lh

Toyota Corolla Repair Manual / Front suspension / Front suspension arm sub–assy lower no.1 Lh

Replacement

Hint

: components:

1. Remove front wheel

2. Disconnect front stabilizer link assy lh (lh (a/t) position)

3. Disconnect front stabilizer link assy rh (lh (a/t) position)

Hint

: remove the rh side by the same procedures as the lh side.

4. Separate front suspension arm sub–assy lower no.1 Lh

  1. Remove the bolt and 2 nuts, and separate the front suspension arm sub–assy lower no.1 Lh from the lower ball joint assy front lh.

5. Separate front suspension arm sub–assy lower no.1 Rh (lh (a/t) position)

Hint

: remove the rh side by the same procedures as the lh side.

6. Separate rack & pinion power steering gear assy (lh (a/t) position)

  1.  remove the 4 bolts, separate the rack & pinion power steering gear assy.

    Notice

    : loosen the bolt since the nut cannot be rotated.

  2.  suspend the rack & pinion power steering gear assy.

7. Suspend engine assy (lh (a/t) position)

8. Separate front suspension crossmember sub–assy (lh (a/t) position)

  1. Remove the 3 bolts and 3 nuts, disconnect the transverse engine engine mounting insulator and engine mounting member sub–assy center from the front suspension crossmember sub–assy.

  1. Remove the 4 bolts.
  2. lower the transmission jack, remove the front suspension crossmember sub–assy.

9. Remove front suspension arm sub–assy lower no.1 Lh

  1. Remove the 2 bolts, nut and front suspension arm sub– assy lower no.1 Lh from the front suspension crossmember sub–assy.

10. Temporary tighten front suspension arm sub–assy lower no.1 Lh

  1. Install the front suspension arm sub–assy lower no. 1 Lh, temporarily tighten the 2 bolts and nut.

11. Install front suspension crossmember sub–assy (lh (a/t) position)

  1.  lift the front suspension crossmember sub–assy up with a transmission jack.

  1. Insert sst to the base hole of the rh side crossmember and rh side of the vehicle.

    Sst 09670–00010

  2.  tighten the bolt temporarily in the order a and b.

  1. Insert sst to the base hole of the lh side of crossmember and lh side of the vehicle.

    Sst 09670–00010

  2.  tighten the bolt temporarily in the order a and b.
  3.  insert sst to the base hole of the rh side of crossmember and rh side of the vehicle.

    Sst 09670–00010

  1. Then tighten the bolt a and b by the specified torque.

    Torque:
    bolt a: 157 nvm (1,601 Kgf·cm, 116 ft·lbf) bolt b: 113 nvm (1,152 Kgf·cm, 83 ft·lbf)

  2.  insert sst to the base hole of the lh side of crossmember and lh side of the vehicle.

    Sst 09670–00010

  3.  tighten the bolt a and b by the specified torque.

    Torque:
    bolt a: 157 nvm (1,601 Kgf·cm, 116 ft·lbf) bolt b: 113 nvm (1,152 Kgf·cm, 83 ft·lbf)

  1. Connect the transverse engine engine mounting insulator and engine mounting member sub–assy center to the front suspension crossmember sub–assy.
  2.  install the 3 bolts and 3 nuts.

    Torque: 52 nvm (530 Kgf·cm, 38 ft·lbf)

12. Install rack & pinion power steering gear assy (lh (a/t) position)

  1.  install the rack & pinion power steering gear assy with the 4 bolts.

    Torque: 58 nvm (591 Kgf·cm, 43 ft·lbf)

13. Install front suspension arm sub–assy lower no.1 Lh

  1. Install the front suspension arm sub–assy lower no.1 Lh with the 2 nuts and bolt to the lower ball joint assy front lh.

    Torque: 89 nvm (908 Kgf·cm, 66 ft·lbf)

14. Install front suspension arm sub–assy lower no.1 Rh (lh (a/t) position)

Hint

: install the rh side by the same procedures as the lh side.

15. Install front stabilizer link assy lh (lh (a/t) position)

16. Install front stabilizer link assy rh (lh (a/t) position)

Hint

: install the rh side by the same procedure as the lh side.

17. Stabilize suspension

  1.  install the front wheel and jack down the vehicle.

    Torque: 103 nvm (1,050 Kgf·cm, 76 ft·lbf)

  2.  bounce the vehicle up and down several times to stabilize the suspension.

18. Fully tighten front suspension arm sub–assy lower no.1 Lh

  1. Fully tighten the 2 bolts and nut.

    Torque: 137 nvm (1,397 Kgf·cm, 101 ft·lbf)

Notice

: tighten the bolt since the nut cannot be rotated.

19. Inspect and adjust front wheel alignment

Disposal
1. Dispose shock absorber assy front lh  fully extend the shock absorber piston rod.  using a drill, make a hole in the cylinder as shown in the illustration to discharge the gas ...

Lower ball joint assy front lh
Replacement Hint: components: 1. Inspect lower ball joint assy front lh Jack up front side of the vehicle.  check the rattle of the lower ball joint assy front lh. 2. Remove front ...

Other materials:

Using a flat bed truck
If you use chains or cables to tie down your vehicle, the angles shaded in black must be 45°. Do not overly tighten the tie downs or the vehicle may be damaged. ■Before emergency towing 1 Vehicles without a smart key system: Put the engine switch in the “ACC” (engine off) or “ON” posi ...

Inspection procedure
1 Inspect dlc3 terminal voltage(ts terminal) Turn the ignition switch to on. measure voltage between terminals ts and cg of dlc3. Ok: voltage: 10 – 14 v 2 Check harness and connector(dlc3 – body ground) Check for open and short circuit in harness and connector between ter ...

Engine immobilizer system
The vehicle’s keys have built-in transponder chips that prevent the engine from starting if a key has not been previously registered in the vehicle’s on-board computer. Never leave the keys inside the vehicle when you leave the vehicle. Vehicles without a smart key system: The indicator light ...

© 2011-2024 Copyright www.tcorolla.net