Toyota Tacoma manuals

Toyota Corolla Repair Manual: Engine rear oil seal

Replacement

1. Remove manual transaxle assy (m/t transaxle)

2. Remove automatic transaxle assy (a/t transaxle)

3. Remove clutch cover assy (m/t transaxle)

  1.  remove the 6 bolts and clutch cover.

4. Remove clutch disc assy (m/t transaxle)

5. Remove flywheel sub–assy (m/t transaxle)

  1. Fix the crankshaft with sst, then remove the 8 bolts and flywheel.

    Sst 09960–10010 (09962–01000, 09963–01000)

6. Remove drive plate & ring gear sub–assy (a/t transaxle)

  1. Fix the crankshaft with sst, then remove the 8 bolts and drive plate & ring gear.

    Sst 09960–10010 (09962–01000, 09963–01000)

7. Remove engine rear oil seal

  1. Using a knife, cut off the oil seal lip.
  2.  using a screwdriver with taping its tip, pry out the oil seal.

Notice

: after the removal, check if the crankshaft is not damaged.

If there is, mend it with a sandpaper (#400).

8. Install engine rear oil seal

  1. Apply mp grease to a new oil seal lip.

Notice

: keep the lip off foreign materials.

  1.  using sst, tap in the oil seal until its surface is flush with the rear oil seal retainer edge.

    Sst 09223–15020, 09950–70010 (09951–07100)

Notice

: wipe off extra grease on the crankshaft.

9. Install flywheel sub–assy (m/t transaxle)

  1. Fix the crankshaft with sst.

    Sst 09960–10010 (09962–01000, 09963–01000)

  1. Clean the bolt and bolt hole.
  2.  apply adhesive to the bolts.

    Adhesive: part no. 09330–00070, Three bond or equivalent.

  3.  install and uniformly tighten the 8 bolts, in several passes, in the sequence shown.

    Torque: 49 nvm (500 Kgf·cm, 36 ft·lbf)

  1. Mark the bolts with paint.
  2.  retighten the bolts by an additional 90 .
  3.  check that the point marked bolts are moved at 90 angle.

10. Install clutch disc assy (m/t transaxle)  sst 09301–00210

11. Install clutch cover assy (m/t transaxle)

12. Install drive plate & ring gear sub–assy (a/t transaxle)

  1. Fix the crankshaft with sst.

    Sst 09960–10010 (09962–01000, 09963–01000)

  1. Clean the bolt and bolt hole.
  2.  apply adhesive to the bolts.

    Adhesive: part no. 09330–00070, Three bond or equivalent.

  3.  install and uniformly tighten the 8 bolts, in several passes, in the sequence shown.
  4.  fix the crankshaft with sst.

    Torque: 88 nvm (897 Kgf·cm, 65 ft·lbf)

13. Install manual transaxle assy (m/t transaxle)

14. Install automatic transaxle assy (a/t transaxle)

Timing gear cover oil seal
Replacement 1. Remove engine under cover rh 2. Remove front wheel rh 3. Remove fan and generator v belt Turn the v–ribbed belt tensioner slowly clockwise and loosen it. Then, remove the f ...

Cylinder head assy
...

Other materials:

Inspection procedure
1 Check d squib circuit(airbag sensor assy center – horn button assy) Disconnect the negative (–) terminal cable from the battery, and wait at least for 90 seconds.  disconnect the connectors between the airbag sensor assy center and the horn button assy. release the airbag act ...

Inspection procedure
1 Inspect fuse(ecu–ig fuse) Remove ecu–ig fuse from the instrument panel j/b.  check continuity of ecu–ig fuse. Ok: continuity 2 Inspect battery Ok: voltage: 10 – 14 v 3 Inspect skid control ecu connector(ig1 terminal voltage) In case of using hand–held tester: ...

Inspection procedure
1 Check hazard warning signal switch assy Check the hazard warning switch continuity, as shown in the illustration and table. Standard: 2 Check turn signal flasher assy 3 Check wire harness (tvip ecu turn signal flasher) Disconnect the tvip ecu and turn signal flashe ...

© 2011-2024 Copyright www.tcorolla.net